1994 Turbo Hose Question- Vacuum Leak

Help, Advice and DIY Tutorials on Volvo's extremely popular car line -- Volvo's 1990s "bread and butter" cars -- powered by the ubiquitous and durable Volvo inline 5-cylinder engine.

1992 - 1997 850, 850 R, 850 T5-R, 850 T5, 850 GLT
1997 - 2000 S70, S70 AWD
1997 - 2000 V70, V70 AWD
1997 - 2000 V70-XC
1997 - 2004 C70

Post Reply
rice240
Posts: 9
Joined: Thu Mar 27, 2014 11:17 am
Year and Model: 90 240 and 94 850T
Location: Houston, Texas

1994 Turbo Hose Question- Vacuum Leak

Post by rice240 »

I am having all sorts of issues chasing down a P0103 code. I have read every possible post. I have a couple of stupid questions... Be nice!

1. Is the insert that has the vacuum line, hose from breather and heating element in the hose from air box to turbo supposed to spin freely? It is in there but it can spin around. Wouldn't that let air in?

2. I did my PCV and my car only had two lower intake manifold bolts. Of course I dropped one and can't find it. Could that cause a significant vacuum leak if all of the top ones are tight and the bottom ones are not?

I did find a tear in the throttle body to IAC hose. I have ordered from Volvo $150.00!

Now my car starts fine and then dies in 20- seconds. I can force it to run with the pedal but it is misfiring. I suppose there is a big vacuum problem causing a lot of this.

I really appreciate everyone's help.

scot850
Posts: 6557
Joined: Mon Apr 05, 2010 2:46 pm
Year and Model: 2000 V70 R
Location: Calgary, Alberta, Canada
Has thanked: 22 times
Been thanked: 309 times

Post by scot850 »

You will need all the manifold nuts to be tight, and I would recommend tightening from the center and working outwards alternating top and bottom nuts. Also be careful as there is a bracket on the RH end of the manifold (when standing in front of the car) at the distributor end, that can fall behind the manifold when refitting it leaving a nice big air gap (ask me how I know that...!).

I would suggest loosening the manifold bolts again and having a full set of nuts for the studs, re-torque it as specified using the process I suggest above. For the IAC hose for the short term you can get a self adhering silicon tape that should be able to fix a split in a hose for a while until the new one arrives. I use this stuff for wiring and it claims to work for plumbing issues as well.

This is the stuff I use:

http://www.canadiantire.ca/en/pdp/fusio ... 0023p.html

Good Luck!

Neil.
2000 V70 R - still being an endless PITA
2006 XC70
2003 Toyota 4Runner V8 Limited
2015 Kia Sportage EX-L
1993 850 GLT -Sold
1998 V70 XC - Sold
1997 Volvo 850 SE NA - Went to niece in California - Sold
2000 V70 SE NA - New project and test bed - Sold

User avatar
gmh
Posts: 158
Joined: Sat May 30, 2009 7:39 pm
Year and Model: 97 850 R Wagon
Location: Lafayette, CO
Has thanked: 15 times
Been thanked: 15 times

Post by gmh »

As Neil says, you need the intake manifold to be on tight. I think they are bolts on the 94, no nuts. For the intercooler hose, duct tape will work in a pinch although not as well as what Neil suggests.
If you haven't paid for the part you ordered from Volvo yet, check out the links below. You can get a whole set of silicone hoses (or 2) for about what that OEM one costs. I have the FCP Sport set and they are fine.

https://www.fcpeuro.com/products/volvo- ... -vol-97tbl
https://www.fcpeuro.com/products/volvo- ... icone-blue
https://www.fcpeuro.com/products/volvo- ... rew-985188
Gary

1969 145S (1987-91)
1973 145E (1989-90)
1981 245 (1990-2001)
1981 244 (1991-2002)
1989 760 Turbo Wagon (1999-2011)
1994 850 Turbo Wagon (2002-2013) burnt valve
2001 V70 2.4T (2009-2017) sold
1997 850 R Wagon (2013-present)
2014 XC60 T6 (2017-present)

User avatar
RickHaleParker
Posts: 5204
Joined: Mon May 25, 2015 2:30 pm
Year and Model: See Signature below.
Location: Kansas
Has thanked: 3 times
Been thanked: 661 times

Post by RickHaleParker »

Sounds like a massive leak in the intake. P0103 = 1-2-1 = Mass Air Flow (MAF). Most likely won't stay running because the ECM is metering not enough fuel because the air mass is a lot higher then what is being measured. Get the intake corrected first.
1998 C70, B5234T3, 16T, AW50-42, Bosch Motronic 4.4, Special Edition package.
2003 S40, B4204T3, 14T twin scroll AW55-50/51SN, Siemens EMS 2000.
2004 S60R, B8444S TF80 AWD. Yamaha V8 conversion
2005 XC90 T6 Executive, B6294T, 4T65 AWD, Bosch Motronic 7.0.

Post Reply
  • Similar Topics
    Replies
    Views
    Last post