IPD sale XeMODeX - Experts in Volvo Electronics
Did you know? 🤔
Logged in users can get email notification of topic replies Log in or register (free).
Amazon Link Buy your stuff using this and it helps MVS!

Maf sensor wiring diagram

Help, Advice, Owners' Discussion and DIY Tutorials on the third generation Volvo V70 wagon and XC70 crossover, and second generation S80. Are you an owner? Prospective owner? Get in here and join us! Start a new topic or comment on an existing thread.

2008-2016 V70
2008-2016 XC70
2007-2016 S80

Grabbysfv88
Posts: 9
Joined: Tue Mar 13, 2018 11:10 am
Year and Model: 2008 S80
Location: CA
Has thanked: 2 times
Been thanked: 0
United States of America
Grabbysfv88

Re: Maf sensor wiring diagram

Post by Grabbysfv88 » Thu Jan 10, 2019 10:41 pm

Ok so far this is where im at .... Hiw do i add a photo



Grabbysfv88
Posts: 9
Joined: Tue Mar 13, 2018 11:10 am
Year and Model: 2008 S80
Location: CA
Has thanked: 2 times
Been thanked: 0
United States of America
Grabbysfv88

Re: Maf sensor wiring diagram

Post by Grabbysfv88 » Thu Jan 10, 2019 11:03 pm

Im sceptical to connect the maf sensor because this is the 4th one i bought last one got fried my fault i tried changing the wire pin out locations because the p0103 code wouldn't clear. I dont understand the reading im getting now .....
20190110_214557.jpg
Welcome any advice at this point. Thanks
You do not have the required permissions to view the files attached to this post.



Grabbysfv88
Posts: 9
Joined: Tue Mar 13, 2018 11:10 am
Year and Model: 2008 S80
Location: CA
Has thanked: 2 times
Been thanked: 0
United States of America
Grabbysfv88

Re: Maf sensor wiring diagram

Post by Grabbysfv88 » Thu Jan 10, 2019 11:19 pm

20190110_214557.jpg
Message_1546665259224.jpg
You do not have the required permissions to view the files attached to this post.



User avatar
pgill
Posts: 143
Joined: Mon Aug 27, 2018 5:42 pm
Year and Model: 2010 S80, 2008 LR2
Location: California
Has thanked: 11 times
Been thanked: 21 times
United States of America
pgill

Re: Maf sensor wiring diagram

Post by pgill » Fri Jan 11, 2019 10:37 am

Take it one step at a time

First 12V power (should only be present at the White wire)
- Key off engine off - a relay should disconnect the 12V and you should measure 0 volts (confirmed)
- Key on engine off - 12 Volts should be present at white wire (confirmed)
- Key on engine off - with the connector removed from the sensor only the white wire should be 12V (confirmed)


Next 5V power (one of the remaining wires should be 5V with the key on engine off)
- Key on engine off - 5V present Confirmed #4 Blue/Grey

Then confirm ground present from ECM
- Key on Engine off - Pin 3 or Pin 5 are very close to battery Voltage with Volt meter from B+ to the Pin (One of these is the Ground)

The remaining two pins should be the signal from the MAF and the signal from temperature sensor

Based on your measurements I don't see 12 Volts on anything except the white wire.

It looks like you have it connected correctly

MAF/IAT sensor description from the manual
MAF.jpg

Thanks

Paul
You do not have the required permissions to view the files attached to this post.



Grabbysfv88
Posts: 9
Joined: Tue Mar 13, 2018 11:10 am
Year and Model: 2008 S80
Location: CA
Has thanked: 2 times
Been thanked: 0
United States of America
Grabbysfv88

Re: Maf sensor wiring diagram

Post by Grabbysfv88 » Sat Jan 12, 2019 10:26 pm

it looks like the middle wire yellow one is giving off 9.v with that wire plugged in I get p0103 maf circuit high input with the yellow wire unplugged I get p0100 maf circuit malfunction, I can clear the code start the car it sounds great 3 or 4 minutes later csr surges at idle put it in drive sounds fine, do a restart and car stalls till I clear the code again I guess it runs fine while the code is pending once confirmed doesn't run so if I plug the blu/gry wire into the middle post the maf should work but the iat would then code right what makes the 5v ref send 9v... and by the way thanks for all the help



Post Reply