IPD sale XeMODeX - Experts in Volvo Electronics
Did you know? 🤔
Logged in users can get email notification of topic replies Log in or register (free).
Amazon Link Buy your stuff using this and it helps MVS!

Tie Rod Jam Nut vs Air Gun Question

Help, Advice, Owners' Discussion and DIY Tutorials on Volvo's stylish, distinctive "P2" platform cars.

2001 - 2007 V70
2004 - 2007 V70 R
2001 - 2007 XC-70
2001 - 2009 S60
2003 - 2007 S60 R

cn90
Posts: 6533
Joined: Wed Mar 31, 2010 9:54 am
Year and Model: 2004 V70 2.5T
Location: Omaha NE
Has thanked: 0
Been thanked: 99 times
United States of America
cn90

Tie Rod Jam Nut vs Air Gun Question

Post by cn90 » Wed Jun 12, 2019 9:15 pm

Hi guys,

I need an opinion re Air Gun for seized Jam Nut (on the Tie Rod).

I need to do an alignment for my 2004 V70 with 110K miles.
I could turn the Inner Tier Rod against the Outer Tier Rod.

- However, the Jam Nut is seized onto the thread of the INNER.
- I have heated the Jam Nut with propane torch for a good 45 sec etc.
- PB Blaster etc. etc.
- Freeze-Off (the CRC stuff) etc.

- I have an Impact Air Gun in my garage.

My question is: from watching the FCPEuro youtube video, the impact gun removed the Jam Nut with ease.
So, if I undo the OUTER from the knuckle, remove the OUTER and expose the Jam Nut just like in the video,
do you think the Impact Gun (with 21-mm socket) will undo the seized nut?


[youtube][/youtube]



---
Jam-Nut.jpg
You do not have the required permissions to view the files attached to this post.


2004 V70 2.5T 100K+
2005 XC90 2.5T 110K+

User avatar
- Pete -
Posts: 216
Joined: Fri Dec 06, 2013 10:13 pm
Year and Model: 01, 04, 04, 04, 06 V
Location: Minnesota/Wisconsin
Has thanked: 22 times
Been thanked: 35 times
United States of America
- Pete -

Re: Tie Rod Jam Nut vs Air Gun Question

Post by - Pete - » Wed Jun 12, 2019 11:20 pm

That jamb nut only has a hold of maybe 3-4 threads worth - it should come loose without too much guff. Make sure you count how many turns when removing the outer tie rod so you’re in the ballpark when re-installing it.

EDIT: I watched the video finally. I'd just do what FCP Jay did. Just make sure you have a good bite on the 13mm hex portion of the shank - maybe a crows foot 13mm, if you can get one on there. Then just blast if off with the impact.

Another easy alternative would be to just cut the jamb nut with a dremel & cutoff wheel & smack with a chisel. Then lube threads & replace jamb nut & carry out alignment from there.


2001 V70XC 142k
2004 V70 AWD 134k
2004 V70R M66 142k
2004 XC70 278k
2006 XC70 155k

jimmy57
Posts: 6414
Joined: Fri Nov 12, 2010 9:25 am
Year and Model: 2004 V70R GT, et al
Location: Ponder Texas
Has thanked: 2 times
Been thanked: 184 times
jimmy57

Re: Tie Rod Jam Nut vs Air Gun Question

Post by jimmy57 » Thu Jun 13, 2019 7:24 am

I have had success using two hammers to get those free. One big hammer on a flat of nut behind and the other big hammer strikes the near flat. Then repeat on another pair of opposing flats.



Post Reply