2002 volvo s60 2.4t PCV still blocked after service/replacement

[cfelberg]

I'll keep on eye on the dipstick. I checked it a couple of times within the last few days and it may have moved up a millimeter if at all. I'm just not sure what the next step would be - I was hoping there was an item that I overlooked that was causing a blockage. Thanks!

Meanwhile just drive with the dipstick up or remove the O-ring. If you smell burning oil inside the car you know it is venting quite a bit.

[MoVolvos]

I'll keep on eye on the dipstick. I checked it a couple of times within the last few days and it may have moved up a millimeter if at all. I'm just not sure what the next step would be - I was hoping there was an item that I overlooked that was causing a blockage. Thanks!

Meanwhile just drive with the dipstick up or remove the O-ring. If you smell burning oil inside the car you know it is venting quite a bit.

I forgot. After I installed the PCV system on my 98 S70 T5 it still did not work well. It's did stop the oil dipstick gushing however. It been awhile and I have not done another PCV but if my memory serves me right I found a plug vacuum hose going to the PTC. I think that's call the PTC.

EDIT: Just read the OP and I cleaned the PTC also and it was a vacuum line going to it that was plugged.

[cfelberg]

Yeah, I was hoping it was due to PTC after reading some posts about it but mine was completely clear, so that's why I was left scratching my head. Car seems to be running well at this point, so I guess I will do what you suggested with the dip stick and continue to monitor it.

[chrism]

If the glove sucked inward real well at idle but then inflated when under load then it might just be that your engine has more blow-by than than the PCV system is capable of evacuating from the crankcase.

[cfelberg]

If the glove sucked inward real well at idle but then inflated when under load then it might just be that your engine has more blow-by than than the PCV system is capable of evacuating from the crankcase.

If this is the case then what is the best course of action?

[MoVolvos]

Yeah, I was hoping it was due to PTC after reading some posts about it but mine was completely clear, so that's why I was left scratching my head. Car seems to be running well at this point, so I guess I will do what you suggested with the dip stick and continue to monitor it.

Do you mean the vacuum line is clear also?

If the glove sucked inward real well at idle but then inflated when under load then it might just be that your engine has more blow-by than than the PCV system is capable of evacuating from the crankcase.

A 5W-40 would do well in the 2002. Try the Rotella T6. An oil change is cheap so worth a try.

[cfelberg]

Yeah, I was hoping it was due to PTC after reading some posts about it but mine was completely clear, so that's why I was left scratching my head. Car seems to be running well at this point, so I guess I will do what you suggested with the dip stick and continue to monitor it.

Do you mean the vacuum line is clear also?


Yes, it is a brand new line.

[MoVolvos]

Yeah, I was hoping it was due to PTC after reading some posts about it but mine was completely clear, so that's why I was left scratching my head. Car seems to be running well at this point, so I guess I will do what you suggested with the dip stick and continue to monitor it.

Do you mean the vacuum line is clear also?

Yes, it is a brand new line.

Are there other small or medium vacuum lines related to the PCV? I think it was around 2012 when I did the work. If so, remove and push air through those to double check.

[cfelberg]

Do you mean the vacuum line is clear also?

Yes, it is a brand new line.

Are there other small or medium vacuum lines related to the PCV? I think it was around 2012 when I did the work. If so, remove push air through those to double check.

There is just one hose that goes directly to the top of the PTC and it is the hose from that long 90 degree hose assembly from the breather box. There are a couple of small vacuum lines that enter the turbo intake tube very near the PTC on their own nipples, but not connected to the PTC directly. Are these the ones you are thinking of?

[MoVolvos]

Are there other small or medium vacuum lines related to the PCV? I think it was around 2012 when I did the work. If so, remove push air through those to double check.

There is just one hose that goes directly to the top of the PTC and it is the hose from that long 90 degree hose assembly from the breather box. There are a couple of small vacuum lines that enter the turbo intake tube very near the PTC on their own nipples, but not connected to the PTC directly. Are these the ones you are thinking of?

Scroll down and see the PTC diagram. It shows a large and small vacuum line. I believe the small one was clogged on mine. It's been awhile.

http://lakesidedp.com/uploadpics/pcv/