Vida CEM swapping

solitaire · Post by **solitaire** » 19 Mar 2021, 11:57

excellent cracker, now with new code P1 work too

: IMG_0183.jpg (114.32 KiB) Viewed 2021 times

: IMG_0182.jpg (89.09 KiB) Viewed 2021 times

: IMG_0181.jpg (95.49 KiB) Viewed 2021 times

: IMG_0184.jpg (122.44 KiB) Viewed 2021 times

Post by **vtl** » 19 Mar 2021, 12:06

Nice!

Post by **RickHaleParker** » 19 Mar 2021, 12:47

solitaire wrote: ↑19 Mar 2021, 11:57 excellent cracker, now with new code P1 work too

Neat package! What is that CAN BUS Transceiver board you used?

Welcome to MVS.

solitaire · Post by **solitaire** » 20 Mar 2021, 04:32

RickHaleParker wrote: ↑19 Mar 2021, 12:47
Neat package! What is that CAN BUS Transceiver board you used?

Welcome to MVS.

"home made"

Post by **RickHaleParker** » 20 Mar 2021, 12:13

solitaire wrote: ↑20 Mar 2021, 04:32 "home made"

Are you going to contribute a Gerber file to the project?

What chips did you use?

Looks like you are drawing power from Vusb. In the current schematic that is listed as an unknown. Can you confirm Vusb has significant power to run the assembly?

solitaire · Post by **solitaire** » 21 Mar 2021, 09:33

RickHaleParker wrote: ↑20 Mar 2021, 12:13 Are you going to contribute a Gerber file to the project?

What chips did you use?

Looks like you are drawing power from Vusb. In the current schematic that is listed as an unknown. Can you confirm Vusb has significant power to run the assembly?

for CAN I use max3051 (3.3V), powered direct from teensy (max 250mA), https://www.pjrc.com/teensy/card10a_rev2_web.pdf
max3051 maximum current 70mA x 2 = 140mA (https://datasheets.maximintegrated.com/ ... AX3051.pdf)

gerber and box for 3D attached

Post by **RickHaleParker** » 21 Mar 2021, 14:01

solitaire wrote: ↑21 Mar 2021, 09:33
for CAN I use max3051 (3.3V), powered direct from teensy (max 250mA), https://www.pjrc.com/teensy/card10a_rev2_web.pdf
max3051 maximum current 70mA x 2 = 140mA (https://datasheets.maximintegrated.com/ ... AX3051.pdf)

USB 5V 500ma is standard.
Teensy 4.0 current is ~100ma.
~100ma + 140MA = ~250ma.
~ 50% of the minimum standard.
No risk of overloading the USB port or coming up short on power.

Post by **ZionXIX** » 21 Mar 2021, 14:32

Is this intended for swapping CEM modules with used ones without dealer involvement?

Post by **vtl** » 22 Mar 2021, 07:27

ZionXIX wrote: ↑21 Mar 2021, 14:32 Is this intended for swapping CEM modules with used ones without dealer involvement?

A part of that, yes. We miss acloning software that pulls the flash and EEPROM from damaged CEM over CAN and writes it to the donor CEM.

zajcis · Post by **zajcis** » 24 Mar 2021, 00:53

solitaire wrote: ↑19 Mar 2021, 11:57 IMG_0181.jpg

Would you like to make some functional copies and sell them to a neighbor country prie Mažeikių?

Vida CEM swapping

Re: Vida CEM swapping