I have a 2011 Volvo XC70 with the position light failure message. Only LH front bulb inop. Bulb/socket/ground all check good. No voltage confirmed at plug.
The rear LH position light works.
The wiring diagram shows the power coming out of the CEM at C1:18.
I cannot find a fuse on the CEM for parking lights. Does anybody know its location?
Does anybody know which connector is C1 ? It would be worthwhile to cycle the plug.
Thanks!
Volvo position light issue
-
davewave365
- Posts: 9
- Joined: 15 Dec 2017, 19:04
- Year and Model: 2011 XC70
- Location: USA
- Been thanked: 2 times
-
davewave365
- Posts: 9
- Joined: 15 Dec 2017, 19:04
- Year and Model: 2011 XC70
- Location: USA
- Been thanked: 2 times
Anybody? Buller?
- volvolugnut
- Posts: 6502
- Joined: 19 Jan 2014, 09:51
- Year and Model: 2001 V70
- Location: Oklahoma USA
- Has thanked: 987 times
- Been thanked: 1075 times
I have the same recurring issue with a right rear position bulb on 2001 V70. Electrical grease helps for a while. Only wiggling the bulb a few times is a consistent short term fix.
On rereading, you have a power supply, not contact problem. Not much help here.
volvolugnut
On rereading, you have a power supply, not contact problem. Not much help here.
volvolugnut
The Fleet:
Volvo: 2001 V70 T5, 1986 244DL, 1983 245DL, 1975 245DL, 1959 PV544, multiple Volvo parts cars.
Mercedes: 2001 E320, 1973 280, 1974 280C, 1989 300E, 1988 300TE, 1979 300TD, parts cars.
2009 Smart Passion
Ford: 1977 F350, 1964 F150 (2), 1938 Tudor Sedan
Farmall tractors: 1956 400 Diesel, 1946 A
John Deere 214 lawn tractor about 1977 model
And others.
Volvo: 2001 V70 T5, 1986 244DL, 1983 245DL, 1975 245DL, 1959 PV544, multiple Volvo parts cars.
Mercedes: 2001 E320, 1973 280, 1974 280C, 1989 300E, 1988 300TE, 1979 300TD, parts cars.
2009 Smart Passion
Ford: 1977 F350, 1964 F150 (2), 1938 Tudor Sedan
Farmall tractors: 1956 400 Diesel, 1946 A
John Deere 214 lawn tractor about 1977 model
And others.
-
davewave365
- Posts: 9
- Joined: 15 Dec 2017, 19:04
- Year and Model: 2011 XC70
- Location: USA
- Been thanked: 2 times
Does the CEM shut off power if the resistance/draw is not correct? Perhaps that is why I got no voltage?
-
- Similar Topics
- Replies
- Views
- Last post
-
- 4 Replies
- 4898 Views
-
Last post by Oly850
-
- 3 Replies
- 1359 Views
-
Last post by RickHaleParker
-
- 59 Replies
- 2097 Views
-
Last post by CoupeC70
-
- 5 Replies
- 9178 Views
-
Last post by iamhives
-
- 2 Replies
- 826 Views
-
Last post by lummert






