NEW TOPIC *** JUNKYARD REQUESTS *****

[helmbelly]

I need a working ETM manufactured AFTER 2013 for my 2001 XC Turbo.

I'm in New Orleans 70122

[abscate]

I need a working ETM manufactured AFTER 2013 for my 2001 XC Turbo.

I'm in New Orleans 70122

These come up routine on eBay for $100-150 ( make offer at $125 or so)

Part number is in the ETM forum below

[BlackBart]

Does anyone ever see the factory trailer hitch for the P2 XC wagon? It's the one that fits up inside the bumper cover, not the ones that hang down below.

Might be heavy and hard to ship.

Volvo factory hitch # 30682087.jpg (40.54 KiB) Viewed 1432 times

Volvo_trailer-hitch.jpg (113.8 KiB) Viewed 1432 times

[Khyren]

I need an early, large flange rear differential viscous coupling for my 1998 V70 AWD. I need the two sholder bolts that hold the lower black plastic valance that goes into the bumper. And lastly I need a set of 03-04 C70 headlights. I have a Xemodex ETM that was taken off of a running 99 XC70 to sell or trade.

Edit: I need the VC on the left and I have the one on the right.

[bmdubya1198]

I need a working ETM manufactured AFTER 2013 for my 2001 XC Turbo.

I'm in New Orleans 70122

See below

I need an early, large flange rear differential viscous coupling for my 1998 V70 AWD. I need the two sholder bolts that hold the lower black plastic valance that goes into the bumper. And lastly I need a set of 03-04 C70 headlights. I have a Xemodex ETM that was taken off of a running 99 XC70 to sell or trade.

Helmbelly above here may be interested in that. The '99-'01 ETMs are all compatible, seeing as it's from a turbo car going onto a turbo car.

[scot850]

Sorry to be dumb, but I don't understand what you are talking about on the black plastic cover and the shoulder bolts.

I have 2 viscous couplings but unfortunately I don't have the earlier version. That went to Anchorage!

Neil.

[Khyren]

Sorry to be dumb, but I don't understand what you are talking about on the black plastic cover and the shoulder bolts.

I have 2 viscous couplings but unfortunately I don't have the earlier version. That went to Anchorage!

Neil.

I'll get a picture of that plastic piece and where the shoulder bolts go. My plastic piece may just be drilled out and they put those bolts in there to fill the hole.

[scot850]

That would certainly be a help.

Neil.

[abscate]

I need an early, large flange rear differential viscous coupling for my 1998 V70 AWD. I need the two sholder bolts that hold the lower black plastic valance that goes into the bumper. And lastly I need a set of 03-04 C70 headlights. I have a Xemodex ETM that was taken off of a running 99 XC70 to sell or trade.

Edit: I need the VC on the left and I have the one on the right.

Could you run the later viscous coupling with the later, longer driveshaft?

I think there are three versions of late p80 AWD driveshafts/couplings, so watch out for that

[bmdubya1198]

I need an early, large flange rear differential viscous coupling for my 1998 V70 AWD. I need the two sholder bolts that hold the lower black plastic valance that goes into the bumper. And lastly I need a set of 03-04 C70 headlights. I have a Xemodex ETM that was taken off of a running 99 XC70 to sell or trade.

Edit: I need the VC on the left and I have the one on the right.

Could you run the later viscous coupling with the later, longer driveshaft?

I think there are three versions of late p80 AWD driveshafts/couplings, so watch out for that

I believe you can, assuming it will bolt up to the diff. The whole angle gear/driveshaft/VC setup is interchangeable.