Nevada1906 1995 850 S60R m56 build thread

[abscate]

And you need it to pin the power steering lines in place so they don’t work harden amd crack….

[Nevada1906]

And you need it to pin the power steering lines in place so they don’t work harden amd crack….

What, like this?

20220415_230202.jpg (2.31 MiB) Viewed 438 times

[abscate]

That’s it , isn’t it? Or am I messed up with something else?

On edit..I forgot my 99 uses a different style bracket as the lines split at-art on the rack differently between -1998 and 1999- model p80s

[Nevada1906]

ENGINE AND TRANSAXLE ARE INSTALLED!!!

I'm aware these aren't Volvo parts, but I'm not in a position to spend upwards of $600 on mounts right now. Besides, I'm planning to install a Quaife LSD and an R clutch at some point in the next few years, so I'll just do the Volvo mounts then.

20220505_174508.jpg (280.65 KiB) Viewed 393 times

Found some nuts and bolts that fit:

20220505_181822.jpg (287.07 KiB) Viewed 393 times

Attached them:

20220505_182309.jpg (340.28 KiB) Viewed 393 times

20220505_182512.jpg (418.25 KiB) Viewed 393 times

20220505_182540.jpg (336.47 KiB) Viewed 393 times

Away we go:

20220505_184020.jpg (248.82 KiB) Viewed 393 times

20220505_184708.jpg (296.71 KiB) Viewed 393 times

20220505_184646.jpg (301.31 KiB) Viewed 393 times

20220505_184706.jpg (291.73 KiB) Viewed 393 times

20220505_184658.jpg (315.72 KiB) Viewed 393 times

Apparently, this site won't let me upload portrait-oriented photos.


And now it's in:

20220505_195943.jpg (353.1 KiB) Viewed 393 times

20220505_195951.jpg (354.43 KiB) Viewed 393 times

20220505_200114.jpg (348.94 KiB) Viewed 393 times

20220505_200059.jpg (310.48 KiB) Viewed 393 times

20220505_200425.jpg (361.88 KiB) Viewed 393 times

20220505_194506.jpg (324.6 KiB) Viewed 393 times

20220505_191439.jpg (466.84 KiB) Viewed 393 times

20220505_191431.jpg (433.8 KiB) Viewed 393 times

In keeping with this car's prototype status, some things don't work right away. For example, the front mount bracket I bought doesn't fit properly. Guess I'll have to buy a different one. Right now, I have a floor jack holding up that corner of the engine.

20220505_200040.jpg (390.84 KiB) Viewed 393 times

Obviously, there's a lot to do. In addition to the front mount bracket, I need the upper and lower torque rods. The old ones are shot.

20220505_201050.jpg (341.66 KiB) Viewed 393 times

20220505_200714.jpg (410.09 KiB) Viewed 393 times

Shift cables need retention circlips. They fit, though:

20220505_201025.jpg (465.91 KiB) Viewed 393 times

Tight fit. The power steering pump reservoir only LOOKS like it's on crooked. It's straight:

20220505_200114.jpg (348.94 KiB) Viewed 393 times

So there it is. I'm sure this is just the start of the interesting (In the Chinese curse sense of the word) part.

[bmdubya1198]

Woohoo!

Yeah, that front engine mount bracket is different. You'll need the correct P80 version.

[scot850]

So nice and shiny!

Is it just the last picture but the engine looks much closer to the RH inner fender than I recall? You might want to check how your axles fit if this is the case.

Neil.

[abscate]

Wait, you have coil on plug ignition on a -1998 style ps pump motor?

Don’t forget to put the aluminum exhaust shield on before the turbo pipe, much easier

[bmdubya1198]

So nice and shiny!

Is it just the last picture but the engine looks much closer to the RH inner fender than I recall? You might want to check how your axles fit if this is the case.

Neil.

It looks about right, it's probably just the angle of the picture. These engines sit pretty close to the inner fender anyway.

[scot850]

You are absolutely right. Looking at it again today, I realised it is the way the picture looks to me and part of what I thought was a narrowed gap is actually the frame lower down!

All looks great!

Neil.

[Nevada1906]

So nice and shiny!

Is it just the last picture but the engine looks much closer to the RH inner fender than I recall? You might want to check how your axles fit if this is the case.

Neil.

It looks about right, it's probably just the angle of the picture. These engines sit pretty close to the inner fender anyway.

The engine and transaxle are properly located on the engine front and rear mounts. It really IS that tight a fit. Serpentine belts are fun jobs because if I remember correctly, the belt's wider than the gap between the engine and the framerail.

See why FWD 5-cylinder cars aren't common?