Vida CEM swapping

Dudde · Post by **Dudde** » 22 Dec 2024, 05:21

Treur wrote: ↑22 Dec 2024, 05:20
Dudde wrote: ↑22 Dec 2024, 05:19
Treur wrote: ↑22 Dec 2024, 05:17 Does anyone know how the odometer is generated in DIM?
What do you mean? How to change the mileage?
Yes

What DIM do you have? Year?

Treur · Post by **Treur** » 22 Dec 2024, 05:24

For example xc90 2007 with mcu mask 0L85D

Treur · Post by **Treur** » 22 Dec 2024, 05:25

I think, the algo is +/- same in all DIM

Dudde · Post by **Dudde** » 22 Dec 2024, 05:27

Treur wrote: ↑22 Dec 2024, 05:25 I think, the algo is +/- same in all DIM

I'll get back to you on this when i have my laptop, don't remember exactly how to do it. But there are software for it and also it is not hard to do it in hex editor.

Treur · Post by **Treur** » 22 Dec 2024, 05:31

I no need to change, I need convert odo data from eeprom to int value

scaro · Post by **scaro** » 22 Dec 2024, 11:58

Treur wrote: ↑22 Dec 2024, 03:10
Dudde wrote: ↑
Read UEM with im608 and program remote
Only new with codes label.

Someone have any clue how to program used fobs? I know its possible if you have the old UEM with keyfob to move fobinfo from UEM to another used UEM. But thinking of keyfob without known UEM? Theres a encryptioncode i think is needed for it to work afaik?

Treur · Post by **Treur** » 22 Dec 2024, 23:23

It's impossible

haifisch · Post by **haifisch** » 23 Dec 2024, 07:17

Treur wrote: ↑22 Dec 2024, 02:36 For cloning you must remove cem from car, and transfer data from MCU and eprom to other cem. I use China xprog for MCU and tl866+ for EPROM.

Thank you! Do I have to desolder the chips to read/write them or connect these tools to some pins on the CEM? I am experienced in programming but only things like web development, SQL, etc or sysadmin stuff. I am noob in embedded systems like ECUs but I am interested(in this field and also in saving my CEM)

Treur · Post by **Treur** » 26 Dec 2024, 05:29

haifisch wrote: ↑23 Dec 2024, 07:17
Treur wrote: ↑22 Dec 2024, 02:36 For cloning you must remove cem from car, and transfer data from MCU and eprom to other cem. I use China xprog for MCU and tl866+ for EPROM.
Thank you! Do I have to desolder the chips to read/write them or connect these tools to some pins on the CEM? I am experienced in programming but only things like web development, SQL, etc or sysadmin stuff. I am noob in embedded systems like ECUs but I am interested(in this field and also in saving my CEM)

You don't need to desolder the mcu, just eprom.

Rolton · Post by **Rolton** » 28 Dec 2024, 07:36

Hello,
2006 V70 CEM - 31394157
Trying to get my CEM pin using T5Luke's UDScrack

Getting bunch of errors, not sure if it's working right

: pin.png (36.15 KiB) Viewed 962 times

Vida CEM swapping

Re: Vida CEM swapping