IPD sale XeMODeX - Experts in Volvo Electronics
Did you know? 🤔
Logged in users can get email notification of topic replies Log in or register (free).
Amazon Link Buy anything with this and it helps MVS!

V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Help, Advice, Owners' Discussion and DIY Tutorials on Volvo's stylish, distinctive "P2" platform cars.

2001 - 2007 V70
2004 - 2007 V70 R
2001 - 2007 XC-70
2001 - 2009 S60
2003 - 2007 S60 R

MikeEvers
Posts: 5
Joined: Sun Apr 12, 2020 5:21 am
Year and Model: Volvo 2002 XC70
Location: Netherlands
Has thanked: 0
Been thanked: 0
Netherlands
MikeEvers

V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by MikeEvers » Sun Apr 12, 2020 5:41 am

hi guys
I have a Volvo V70 XC. built in 2002. 2.4 turbo

Fault code: P0340
Volvo fault code ECM-3000

fault can be cleared. after starting, the fault immediately returns

The Volvo specialist checked the timing of te timingbelt and is it stil correct. They replaced the CAM sensor. Also they measure the wires from ECM to the camsensor.

So yesterday it checked the voltage hem disconnected from the cam sensor bleu/black and red/whiteboards cable

Pin 1 5 volts
Pin 3. 3volts

After That i measure on the ECM connector the values are the same as on the cam sensor connector (disconected connector)



I think the 3 volts are suspicious.

could this indicate a faulty ECM?

who has experience with this?


Thanks!

Mike
Last edited by MikeEvers on Sun Apr 12, 2020 11:22 am, edited 2 times in total.

User avatar
RickHaleParker
Posts: 4216
Joined: Mon May 25, 2015 2:30 pm
Year and Model: See Signature below.
Location: Kansas
Has thanked: 3 times
Been thanked: 539 times
United States of America
RickHaleParker

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by RickHaleParker » Sun Apr 12, 2020 6:00 am

The 3V is inconclusive. You might be seeing the RMS value of the signal.
What are you using as the ground reference?

With the key off. Check for shorts 1-2, 1-3 & 2-3.
Clean the connectors on the Camshaft sensor and the ECM.
Check for open wires between the Sensor and the ECM.

Based on your measurements:
One wire should be Voltage. it looks like that is pin one.
One wire is signal looks like that is pin two.
Pin three is most likely ground.
All three wires are connected to the ECM.
Last edited by RickHaleParker on Sun Apr 12, 2020 6:13 am, edited 1 time in total.
--------
Platform: P80 1998 C70, B5234T3, 16T, AW50-42, Bosch Motronic 4.4, Special Edition package, Plant: Uddevalla Sweden.
Platform: X40 (Nedcar) 2003 S40, B4204T3, 14T twin scroll AW55-50/51SN, Siemens EMS 2000. Plant: Born Netherlands.
Platform P2 2005 XC90 T6 Executive, B6294T, 4T65 AWD, Bosch Motronic 7.0, Plant Torslanda Sweden.
Platform P2 2004 S60R, B2524T4, AW50/51 AWD, Bosch Motronic 7.0, BorgWarner K24 turbocharger, Plant Ghent Belgium.

User avatar
darrylrobert
Posts: 180
Joined: Fri Mar 06, 2020 6:25 am
Year and Model: 2001 v70xc
Location: australia
Has thanked: 3 times
Been thanked: 7 times
Australia
darrylrobert

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by darrylrobert » Sun Apr 12, 2020 6:10 am

It should be 4.7volts i think, what did the 'Volvo specialist' say about the 3 volts?

MikeEvers
Posts: 5
Joined: Sun Apr 12, 2020 5:21 am
Year and Model: Volvo 2002 XC70
Location: Netherlands
Has thanked: 0
Been thanked: 0
Netherlands
MikeEvers

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by MikeEvers » Sun Apr 12, 2020 8:34 am

About the Volvo specialist.


I'm not going to post a reference but ... its a specialist in Volvo V70 🙈

diagnosis cost me a total of 800 euros without result.

1st time diagnosis. 6 hours of work. replaced the cam sensor and housing (before it was steel, now its a plastic one) cost 600 euros. malfunction after starting 2x.

2nd diagnosis. having measured the wiring and checked timing belt. costs 250 euros.

concession. learn to live with it. or it will become much more expensive


They told me that before there was maby a engine swap. Based on Some handmade markings on the engine
Last edited by MikeEvers on Sun Apr 12, 2020 9:11 am, edited 1 time in total.

MikeEvers
Posts: 5
Joined: Sun Apr 12, 2020 5:21 am
Year and Model: Volvo 2002 XC70
Location: Netherlands
Has thanked: 0
Been thanked: 0
Netherlands
MikeEvers

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by MikeEvers » Sun Apr 12, 2020 9:09 am

The bleu/black Wire has 3 volt on the connector to the cam sensor. (Connector disconected)

Red/white 5 volts

Measure with a multimeter. With the ground on de enginebay ground spot.

What i notice is that they replaced the connector on the cam sensor side.

The black cable is in the middle.
Blue/black on the left side
Red/white on the right side.

Can someone confirm this is correct?

User avatar
RickHaleParker
Posts: 4216
Joined: Mon May 25, 2015 2:30 pm
Year and Model: See Signature below.
Location: Kansas
Has thanked: 3 times
Been thanked: 539 times
United States of America
RickHaleParker

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by RickHaleParker » Sun Apr 12, 2020 10:53 am

MikeEvers wrote: ↑
Sun Apr 12, 2020 9:09 am
The black cable is in the middle.
Blue/black on the left side
Red/white on the right side.

Can someone confirm this is correct?
From the Electrical Wiring Diagram (EWD) TP3961202.

Pin #1 Red-White.
Pin #2 Black
Pin #3 Blue-Black.
--------
Platform: P80 1998 C70, B5234T3, 16T, AW50-42, Bosch Motronic 4.4, Special Edition package, Plant: Uddevalla Sweden.
Platform: X40 (Nedcar) 2003 S40, B4204T3, 14T twin scroll AW55-50/51SN, Siemens EMS 2000. Plant: Born Netherlands.
Platform P2 2005 XC90 T6 Executive, B6294T, 4T65 AWD, Bosch Motronic 7.0, Plant Torslanda Sweden.
Platform P2 2004 S60R, B2524T4, AW50/51 AWD, Bosch Motronic 7.0, BorgWarner K24 turbocharger, Plant Ghent Belgium.

MikeEvers
Posts: 5
Joined: Sun Apr 12, 2020 5:21 am
Year and Model: Volvo 2002 XC70
Location: Netherlands
Has thanked: 0
Been thanked: 0
Netherlands
MikeEvers

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by MikeEvers » Mon Apr 13, 2020 1:05 pm

Ok thanks!

The wiring is correct.

In the basics: cam sensor with 3 wires . 1. Power 2 signal 3 ground .

Is it normal to have. 2 powers instead of 1power and one ground?

Thanks all!

User avatar
RickHaleParker
Posts: 4216
Joined: Mon May 25, 2015 2:30 pm
Year and Model: See Signature below.
Location: Kansas
Has thanked: 3 times
Been thanked: 539 times
United States of America
RickHaleParker

Re: V70 2.4 turbo P0340 cam sensor malfunction ecm-3000

Post by RickHaleParker » Mon Apr 13, 2020 1:24 pm

MikeEvers wrote: ↑
Mon Apr 13, 2020 1:05 pm
Is it normal to have. 2 powers instead of 1power and one ground?
--------
Platform: P80 1998 C70, B5234T3, 16T, AW50-42, Bosch Motronic 4.4, Special Edition package, Plant: Uddevalla Sweden.
Platform: X40 (Nedcar) 2003 S40, B4204T3, 14T twin scroll AW55-50/51SN, Siemens EMS 2000. Plant: Born Netherlands.
Platform P2 2005 XC90 T6 Executive, B6294T, 4T65 AWD, Bosch Motronic 7.0, Plant Torslanda Sweden.
Platform P2 2004 S60R, B2524T4, AW50/51 AWD, Bosch Motronic 7.0, BorgWarner K24 turbocharger, Plant Ghent Belgium.

Post Reply
  • Similar Topics
    Replies
    Views
    Last post