IPD sale XeMODeX - Experts in Volvo Electronics
Did you know? 🤔
Logged in users can get email notification of topic replies Log in or register (free).
Amazon Link Buy your stuff using this and it helps MVS!

What did you do to your Volvo today?

Help, Advice and DIY Tutorials on Volvo's extremely popular car line -- Volvo's 1990s "bread and butter" cars -- powered by the ubiquitous and durable Volvo inline 5-cylinder engine.

1992 - 1997 850, 850 R, 850 T5-R, 850 T5, 850 GLT
1997 - 2000 S70, S70 AWD
1997 - 2000 V70, V70 AWD
1997 - 2000 V70-XC
1997 - 2004 C70

User avatar
amblerman
Posts: 264
Joined: Wed Jan 18, 2017 3:29 pm
Year and Model: 1999 s70
Location: Pennsylvania
Has thanked: 1 time
Been thanked: 19 times
United States of America
amblerman

Re: What did you do to your Volvo today? (now Sticky!!)

Post by amblerman » Tue Jun 04, 2019 4:40 pm

This weekend I tackled an AC clutch re-shim on my 1999 s70.

I had the classic symptoms of AC being cold for a few moments and then it would get warm. I measured the gap and it was greater than my larger gauge which was .866 mm.

The job wasn't too bad. I basically followed many of the online videos for removing the alternator .
Some of the videos I watched have people remove the fan shroud and removing the alternator by moving it across the front of the engine and out where this is more space. On my 99 s70 I didn't have to do that. It just comes out near the ECM. Pretty darn easy.

For the puller, I follow the template here;
https://www.matthewsvolvosite.com/downl ... AC-Fix.pdf

However, I just made it out of plywood. Worked like a charm. I did hot melt glue a fender washer onto plywood where it would make contact with the bolt screwed into the clutch so it wouldn't just sink into the plywood as I tightened the 3 5mm bolts. Popped the clutch right off. I threw the tool out by accident and never took a picture of it. Stupid me. Just a square of plywood with 3 holes drilled into it based on the template in the link above.

it turns out that someone had already been in there and had removed the medium sized shim . That's probably the one I needed as using any of the remaining shims would have left me in a Goldilocks scenario: Thick shim would have left the gap too big and the thin shim would have left the gap too small.

So I made one out of some aluminum gutter flashing.

Gap is now .4 mm and AC is cold.

Two tips.

1) Watch out for holes in the frame. There is a hole in the subframe just below the center bolt for the AC clutch. I dropped the bolt and of course it fell into the frame almost to be lost forever. So tape over the holes first.

2) I was able to feel the bolt inside the frame but I couldn't grab it. So I stuck a rare earth magnet inside my glove. Worked well
magnet.png

(edited for spelling)
You do not have the required permissions to view the files attached to this post.



User avatar
abscate
MVS Moderator
Posts: 19268
Joined: Sun Feb 17, 2013 5:54 pm
Year and Model: 99T5 ,99S70,2005V70
Location: NYC, ALBANY NY
Has thanked: 234 times
Been thanked: 768 times
Trinidad & Tobago
abscate

Re: What did you do to your Volvo today? (now Sticky!!)

Post by abscate » Tue Jun 04, 2019 7:38 pm

. So I stuck a rare earth magnet inside my glove
this is Huge !


Empty Nester
A Captain in a Sea of Estrogen
1999-V70-T5M56 2005-V70-M56 1999-S70 VW T4 BMW
Link to Maintenance record thread
Link To Volvo Glossary

User avatar
amblerman
Posts: 264
Joined: Wed Jan 18, 2017 3:29 pm
Year and Model: 1999 s70
Location: Pennsylvania
Has thanked: 1 time
Been thanked: 19 times
United States of America
amblerman

Re: What did you do to your Volvo today? (now Sticky!!)

Post by amblerman » Tue Jun 04, 2019 10:11 pm

abscate wrote:
Tue Jun 04, 2019 7:38 pm
. So I stuck a rare earth magnet inside my glove
this is Huge !
I had a few false starts with this idea as I was trying to hot melt glue or tape the magnets to some stick or rubber hose but it wasn't working. I then started thinking of some way I could attach it to my glove so I could just use my finger. And then I had that DOH! moment when I finally realized I could just put it IN the glove. No complicated attachments or anything.

I had a brief moment of fear when I worried my finger would get stuck in the hole in the frame but thankfully that embarrassing situation didn't manifest. The magnet I used is a tiny cylinder type magnet. about the size of a grain or rice. Those rare earth magnets are so powerful.

Those spherical rare earth magnets that are parts of toys would well too.

I thought back to all those bolts and nuts I've dropped in hard to reach places. A magnet in a glove would make getting those so easy.

I probably will never drop a bolt ever again.

-A



User avatar
ZionXIX
Posts: 487
Joined: Mon Aug 11, 2014 2:47 pm
Year and Model: 1996 850 Turbo S/W
Location: Texas
Has thanked: 8 times
Been thanked: 35 times
United States of America
ZionXIX

Re: What did you do to your Volvo today? (now Sticky!!)

Post by ZionXIX » Tue Jun 04, 2019 10:24 pm

MVS will never be the same. Soon everyone will be shoving magnets into their gloves.



User avatar
abscate
MVS Moderator
Posts: 19268
Joined: Sun Feb 17, 2013 5:54 pm
Year and Model: 99T5 ,99S70,2005V70
Location: NYC, ALBANY NY
Has thanked: 234 times
Been thanked: 768 times
Trinidad & Tobago
abscate

Re: What did you do to your Volvo today? (now Sticky!!)

Post by abscate » Wed Jun 05, 2019 1:03 am

So many applications

I just did three battery replacements on iPhones and holding those small screws just got easy

I’ll cut off a finger to make a magnetic finger cot for that next time


Empty Nester
A Captain in a Sea of Estrogen
1999-V70-T5M56 2005-V70-M56 1999-S70 VW T4 BMW
Link to Maintenance record thread
Link To Volvo Glossary

User avatar
jvl
Posts: 189
Joined: Mon Oct 03, 2016 3:33 am
Year and Model: 1999 V70 XC
Location: Netherlands
Has thanked: 17 times
Been thanked: 7 times
Netherlands
jvl

Re: What did you do to your Volvo today? (now Sticky!!)

Post by jvl » Mon Jun 10, 2019 12:27 pm

Not today, but over the past few weeks:

- Oil change
- DIY toe-in alignment which turned out pretty well
- Put my propshaft up for sale, since I deleted the angle gear after finding out it was broken. The propshaft had just been rebuilt, so that sucked. Ad here (based in Netherlands...): https://link.marktplaats.nl/m1418529110

Camping season preparations:
- Bought and installed a rooftop tent which is awesome for short camping trips! We love a 'ground tent' but the one we have is quite time consuming to set up, so more suitable for longer trips.
- Electrical work and planning: ordered new solar panel setup (old bulky panel I have been using doesn't combine well with the rooftop tent)
- Laid out camping kit to fit bottom drawer, ordered parts to install drinking water tank + tap in bottom drawer

Temparatures are rising, getting excited to do more road trips!
You do not have the required permissions to view the files attached to this post.


1999 V70XC. Stock, except.... I like tinkering:
electronics
2nd battery (with isolator)
2200w pure sine wave inverter
LED Work lights in tailgate
LED traffic advisor
RC parking lights

audio
stock tweeters front and back
8" underseat powered sub

camping extras
'drawer system' in trunk
solar panel on roofrack



Feel free to PM for pics

User avatar
cmblackburn
Posts: 248
Joined: Sat Apr 07, 2012 4:23 am
Year and Model: 1998 S70 T5
Location: Durham, North Carolina
Has thanked: 0
Been thanked: 0
United States of America
cmblackburn

Re: What did you do to your Volvo today? (now Sticky!!)

Post by cmblackburn » Mon Jun 10, 2019 8:31 pm

62587936_10219240070692951_4297350053661507584_o.jpg
I did...a pretty big thing!
...Now fighting with master cylinder installation, and then have the long road ahead of me with the rest of the swap.
I miss driving this junkheap.
You do not have the required permissions to view the files attached to this post.


1998 S70 T5, 267k "The Blue Turd" Dead again, manual swapping
2004 S40 2.4i, 164k "Cosmo"
2001 Ford Escape XLT, 198k "The Magic School Bus"

User avatar
bmdubya1198
Posts: 3395
Joined: Tue Dec 30, 2014 10:45 am
Year and Model: '98 V70 GLT
Location: Charlotte, NC
Has thanked: 32 times
Been thanked: 108 times
United States of America
bmdubya1198

Re: What did you do to your Volvo today? (now Sticky!!)

Post by bmdubya1198 » Mon Jun 10, 2019 9:53 pm

Nice! That master cylinder is a ton of fun to install...

Did you decide on yanking the whole thing out the top or dropping the trans from underneath?


2000 V70R Venetian Red/Charcoal M56 Swapped 191k
2000 S70 GLT Mystic Silver/Taupe 2??k
2003 S60 2.4T Silver/Black 108k
2007 XC90 V8 AWD Sport Titanium Grey/Black 160k
1993 944 Base Beige/Beige 221k
1992 Miata Mariner Blue/Black 146k
Sold-
1998 V70 GLT Black/Beige 193k
1998 S90- Silver/Gray 207k
1995 850 GLT Tropic Green... crushed
2001 S60 2.4T Black/Black 230k
1988 744 Turbo M46 Beige Metallic/Beige 188k- Never should have sold it


Need used parts? PM me!

User avatar
cmblackburn
Posts: 248
Joined: Sat Apr 07, 2012 4:23 am
Year and Model: 1998 S70 T5
Location: Durham, North Carolina
Has thanked: 0
Been thanked: 0
United States of America
cmblackburn

Re: What did you do to your Volvo today? (now Sticky!!)

Post by cmblackburn » Mon Jun 10, 2019 10:53 pm

bmdubya1198 wrote:
Mon Jun 10, 2019 9:53 pm
Nice! That master cylinder is a ton of fun to install...

Did you decide on yanking the whole thing out the top or dropping the trans from underneath?
Yanking the whole thing out the top. I dropped my Escape's out the bottom of the car using an engine support bar, but with the addition of having to drop the subframe and all on the Volvo I'll just as soon yank it back out the top, even though I just did that 5k ago during the engine replacement.


1998 S70 T5, 267k "The Blue Turd" Dead again, manual swapping
2004 S40 2.4i, 164k "Cosmo"
2001 Ford Escape XLT, 198k "The Magic School Bus"

User avatar
bmdubya1198
Posts: 3395
Joined: Tue Dec 30, 2014 10:45 am
Year and Model: '98 V70 GLT
Location: Charlotte, NC
Has thanked: 32 times
Been thanked: 108 times
United States of America
bmdubya1198

Re: What did you do to your Volvo today? (now Sticky!!)

Post by bmdubya1198 » Tue Jun 11, 2019 8:23 am

cmblackburn wrote:
Mon Jun 10, 2019 10:53 pm
Yanking the whole thing out the top. I dropped my Escape's out the bottom of the car using an engine support bar, but with the addition of having to drop the subframe and all on the Volvo I'll just as soon yank it back out the top, even though I just did that 5k ago during the engine replacement.
That's definitely how I'd do it. I feel like it's much easier to do it that way if you don't have a lift. I pulled it from the bottom last time, not doing that again!


2000 V70R Venetian Red/Charcoal M56 Swapped 191k
2000 S70 GLT Mystic Silver/Taupe 2??k
2003 S60 2.4T Silver/Black 108k
2007 XC90 V8 AWD Sport Titanium Grey/Black 160k
1993 944 Base Beige/Beige 221k
1992 Miata Mariner Blue/Black 146k
Sold-
1998 V70 GLT Black/Beige 193k
1998 S90- Silver/Gray 207k
1995 850 GLT Tropic Green... crushed
2001 S60 2.4T Black/Black 230k
1988 744 Turbo M46 Beige Metallic/Beige 188k- Never should have sold it


Need used parts? PM me!

Post Reply
  • Similar Topics
    Replies
    Views
    Last post