Volvo Forum + help for owners

It doesn't look like this issue was ever resolved, any updates?

I've had the brake booster sensor cause erratic shifting and hard down shifting...I mean slamming down. I replaced the brake booster sensor after diagnosis and she shifted perfectly for years after.

My wife was driving the 2004 XC70 for a couple of hours, then the 2-3 upshift flares. It's got no 3rd gear at all but it will bypass 3rd if I use the sport shift. I met up with her and drove it home. There's no flashing lights, NO red triangle, no CEL. No messages on message screen...nothing. I hoo...

Its a beautiful p80, shame where it got hit.

Check the tire wear, if the wheel alignment is off you will have terrible high speed wet traction...especially if it's raining hard enough to make big puddles on a highway.

What happened? That doesn't look encouraging from the pic shown , do you have anymore pics?

If I lived closer to you I'd come get that p80 and I have a 1998 rear propeller shaft from the 98 v70xc I had years ago. 1 of my coolant lines split open and i lost all of my coolant, the level sensor was sticking so I never got the warning light on the dash cluster. Anyway the motor hydrolocked, I ...

Help! We need to change the transmission fluid on our 2016 XC60 with 75K. Owners manual and dealer says tranny is sealed and will last a "lifetime." We would like to drive ours until the wheels fall off. The fluid needs to be changed. Do you have a schematic anywhere showing any fill or drain plugs...

My wife totalled her XC90 T6 a couple of months ago and were looking at this 2017 XC60 T6 with 30k on the odometer. We like the newer XC90 but it's so much bigger than her XC90 was, so were considering the XC60 instead. She's been driving a BMW x3 and she really misses her Volvo, so she wants to tra...

If no previous flaring that would indicate the 3rd gear band was not slowing wearing out over time so maybe the problem can be corrected with the servo cover and new o-rings. Is 3rd gear completely gone now even at cold ATF temps too? There wasn't any transmission work done previously before the pr...

Never had issue before with the A/T. If no previous flaring that would indicate the 3rd gear band was not slowing wearing out over time so maybe the problem can be corrected with the servo cover and new o-rings. Is 3rd gear completely gone now even at cold ATF temps too? There wasn't any transmissi...

My wife was driving the 2004 XC70 for a couple of hours, then the 2-3 upshift flares. It's got no 3rd gear at all but it will bypass 3rd if I use the sport shift. I met up with her and drove it home. There's no flashing lights, NO red triangle, no CEL. No messages on message screen...nothing. I hoo...

The only thing I would know to do is pull out the servo assy and put in the IDP servo kit. Make sure everything looks ok. Three drain and fills, and hope for the best. I'd try Seafom Trans Tune after the above didn't work. Thank you for your response. I ordered the B4 Servo kit from IPDUSA.COM a fe...

What years are affected by this servo cap? I have a 2004 XC70 that just lost 3rd gear, no CEL, no flashing lights, no warning on dash, no red triangle nothing but a DTC store in ecu... p0733 gear3 incorrect ratio.

My wife was driving the 2004 XC70 for a couple of hours, then the 2-3 upshift flares. It's got no 3rd gear at all but it will bypass 3rd if I use the sport shift. I met up with her and drove it home. There's no flashing lights, NO red triangle, no CEL. No messages on message screen...nothing. I hook...

Unfortunate. You can always look for a broken one and move your fresh parts over. The fun never ends. You got that right...it never ends, what a waste. What can say is that this XC90 T6 has seen 3 separate occasions where deer actually ran into our XC90 and this accident here, everytime this vehicl...

The L/F wheel hit the bottom of a pole, the cement block at the bottom of pole. It was dark, foggy and very humid, so inside of windows were wet from a/c humidity. The tire was sticking during the wheel turning left. The tire hit the cement post and pulled the XC90 into pole. The CV axle broke insid...

Thanks. I figured it was something like that. I even tried setting my Garmin in it some time ago, but my nuvi is too new for this cradle. I just hate that they punched 3 holes in the speaker grille and yanked out the speaker just for an accessory that would be obsolete within 4-5 years. It would be...

Cleverly, while replacing rotted hoses in our 2005 XC90 2.5T, I snapped the end off what I presume is a check valve on one of the 9.5mm manifold vacuum hoses(?) https://lh3.googleusercontent.com/tuIVY9tTV9v-43DJlXjf_3FX12eQZp6_ffez_tLmNIDWN3yAmQvITMYNFtkjw4cwg1lfJqdOQhanm5gmizx5iRdaKJX6JaQwpODtI_dg...

A must read thread from the MVS maestro https://www.matthewsvolvosite.com/forums/viewtopic.php?t=91985 [/quote] Yes fcp does make excellent videos for Volvo products. FCPEURO.COM has been my go to for years...FCPGROTON.com . We found them back when we had our 1996 Volvo 850 GLT . I literally just re...

Ok, I have a 2003 XC90 T6- I know great transmission! Anyway, it has 82,000 miles, the transmission was of course out, had it dropped and the clutch packs replaced and anything else in the master rebuild kit. Put it all together and is was fine for a few weeks. Now I have a “Service Transmission” m...

Ok, I have a 2003 XC90 T6- I know great transmission! Anyway, it has 82,000 miles, the transmission was of course out, had it dropped and the clutch packs replaced and anything else in the master rebuild kit. Put it all together and is was fine for a few weeks. Now I have a “Service Transmission” m...

Starting this job this weekend. I've read write-ups and watch some videos. One video in particular literally only removed the control arm and ball joint, and then later replaced the sway bar link. So my first question is this: If the control arm and ball joint are both being replaced, is there a re...

After replacing everything on the front end of our 2004 XC90 T6 (Ball joints, inner/outer tie rods, sway bar links, Macpherson struts/entire assembly) I felt confident to purchase a new set of Pirelli Scorpions gen 2 I believe. After that we did a wheel alignment. We went through a set of Hercules a...

My new 05 T6 XC90 came with 235/60/R18 Michelins which were totally shot at 20K. People can justify it however they want, but this is totally unsatisfactory to me. I do not think Michelins are at all worth the difference in price. I then tried Kumho Road Ventures from Tire Rack, which wore out just...

Hello, 2006 XC90 v8. As the subject states the high beam headlights will not turn off unless the battery is disconnected or the fuses in the CEM are removed. These headlights are the normal lights not the self leveling xenon lights. The low beams function normally and all the other functions of the...

I have a brand new Vida Dice for sale. In absolutely full disclosure, I could not get it to work. But, I believe it is my computer more than the unit itself and trying to make it Windows 10 vice Windows 7. This unit powers up fine, but I was getting am "Invalid Descriptor Device Descriptor" in the ...

Even when you disconnect the battery the learning curve for the ECM/Network is extremely quick...regardless she should still have boost. If you have a DTC for the ETM the you need to retrace your steps in that area. Is there any messages on the cluster screen?

You really have to take off the tubing for the turbo system to inspect for leakage. You won't get any DTC's for leakage in one of those soft tubes. Check all of your vacuum lines for your EVAP system. Do you a scan tool for reading long term and short term fuel trims?

I've seen leaves, pine needles and those squiggly things from oak trees clog up the hood cowl drains so bad that during a heavy rainstorm the water came inside through HVAC system. The vehicle was a 90's Nissan Maxima that had the ECU behind the head unit cluster positioned on the center hump...anyw...

I just replaced the thermostat on our 2004 XC90 T6, while I had everything apart I replaced the thermostat housing, temp sensor, gaskets, 2 resevoir coolant hoses, coolant, clamps and installed a brass fitting after removing the plastic fitting that came with the new Volvo thermostat housing.

The drain tubes behind A-pillars are known issue for early model XC90, especially of there sitting unused for long periods. You have to resolve leak issues first, your just going to have same issues. The CEM is connected to all the other modules, if your CEM is fouled up then your going to have all ...

My wife's 2004 VOLVO XC90 T6 has issues with cd player not working. When you first start up ignition the cd player sounds like it's searching for a disc but never finds a disc. Her AM/FM radio still works. Anyway after reading this thread it sounds like the head units have a bunch of issues on these...

befarrer wrote: ↑Wed Mar 11, 2020 12:01 pm

IMG_20200309_171718.jpg

Finally washed winter off my car.

The nameplate, "D13 Volvo Power "
What does that stand for?
Is that a special edition V70 p80chassis?

Thank you for posting your write up, excellent work. I'm swapping out the thermostat housing, thermostat, temp sensor, every gasket, hardware, hoses to coolant reservoir and upgraded the plastic elbow with a brass elbow from IPDUSA.COM. My question to you is this: Did you lose a lot of coolant when ...

Good one, you will notice cleaner shifting and less movement when putting the power on. I opted for a PU upgrade, but it brings some vibration into the cockpit, a tradeoff not everyone is willing to make ;) https://live.staticflickr.com/893/27630801087_c96fe62d16_b.jpg Volvo S80 2.4T New vs Old Gea...

To start I replaced the Lower Torque Mount/Transmission Mount. 20200214_171528.jpg 20200216_103359.jpg Next I installed the Volvo tire valve caps. 20200216_105645.jpg New HID bulbs for my USDM factory HID headlights open-uri20140604-30668-2jcwlm.jpeg This Hutchinson engine mount is the actual factor...

Thank you! CORTECO seals will save over Volvo's -- $8 v $21. Oil leak monitoring is ongoing, since a slight wetness has emerged at the base of TB inner cover after the last week's cleanup. The oil filter and seal were Mahle, but from Amazon. Breaking crankshaft nut appears daunting -- Bauer deliver...

When using the crankshaft counterhold tool you have to remove the starter to install tool, so yes its an extra procedure. Sometimes you can get by with a good 1/2" impact wrench whether it's air/cordless. I have the rear cam locking tool set that comes with the crankshaft locking tool, plus everythi...

Do I need to replace long T55 #18? Here is a working parts list on VVT and related task: - Hub/Pulley #1275363 (Volvo) - Intake Camshaft Seal -- Sealing Ring #9458309 (Corteco) - Exhaust Camshaft Seal -- Sealing Ring #9458309 (Corteco) - Engine Camshaft Plug Cap #1397381 (Volvo) - Engine Expansion ...

I'd replace everything while you have it apart...front/rear cam seals, gaskets, water pump, tensioner, TB, front hub seal or actual VVT hub. I'd Buy factory parts or factory parts that come in the manufacturer's box instead of a Volvo box when possible.

I have an '04 V70 NA, which I have had for about a year. For as long as I can remember the "Brake Failure, Stop Safely" message has been on, the only ill effect I can recall is inoperable ABS in the snow. In fact the car would pull itself to the right making me think the left hand front brake was n...

I'd encourage you to have a new filter/finned cover & a liter of fresh AOC oil on hand. If you end up needing to replace the pump you will want to do the filter at the same time. These guys made a pretty great video. https://www.youtube.com/watch?v=VKDrJumrm78 EDIT: I personally would not take the ...

levi_850 wrote: ↑Sun Feb 02, 2020 2:42 am Updated my factory headlights with projectors.

Is that a retrofit?

20191223_161249.jpg 20191223_161235.jpg 20191223_161229.jpg 20191223_160832.jpg 2004 Volvo XC70 model w/Factory HID headlight assemblies/self leveling system. The tensioner pulley for the serpentine belt broke off, just the actual plastic pulley. Everything else on the tensioner was still intact, i...

At those miles & never having changed the AOC oil nor filter, I’d say the pump is the most likely culprit, but you will have to do your own investigative work to verify. Do you have ViDA? Or can you get to somebody who does? My first one I troubleshot without ViDA & replaced without an outline of t...

With the ignition & engine off Haldex/DEM pump is not running. If you cannot spin the driveshaft by hand that is a good sign - it verifies your angle gear & collar sleeve should be in working order, but it has nothing to do with verifying the functional status of the AOC/Haldex/DEM pump. Yes - it i...

Pentofrost_NF (1).pdf: Pentofrost NF; (129.56 KiB) Downloaded 39 times

This should answer any questions in reference to this product.

The AOC AWD system is not active without engine running. The hydraulic pump is not turned on until the engine running data bit is broadcast on network. If you do the same things with eng running and you do not have considerable effort to turn the wheel then there is a problem. The AOC will have a l...

Pento Frost NF OK that looks to be a with-silica type. Says it's "bright blue" so I guess it's HOAT too? (They don't say). Doesn't look like this is popular here, I'll have to call around. Pento Frost NF is made by Pentosin, I believe Pentonsin manufactures the coolant for Volvo branded bottles. Ye...

On our 2004 XC70 (P2 Chassis) the sunroof got stuck open because the alarm module (Siren/module) failed. I was able to manually close the sunroof by removing the motor, then replaced the motor(just like a door window regulator motor). Anyway I replaced the alarm module with a new one from a reputabl...

Pento Frost NF

Just got a 2005 s60 and i noticed there is a gap on the top of the strut. Structs seem fairly new. Could I just tighten the top bolt or were they installed wrong. Car handles bumps fine. Madness Can you post some pics of the strut gap your referencing? Thank you June, lol. I knew what OP meant I ju...

I hope it works out for you, I personally dont like adding more couplers or T joints because its another area for potential leaks but I like the ingenuity.

Post some pics of said issue.

volvomadness wrote: ↑Wed Jan 22, 2020 10:16 pm Just got a 2005 s60 and i noticed there is a gap on the top of the strut. Structs seem fairly new.
Could I just tighten the top bolt or were they installed wrong.

Car handles bumps fine.

Madness

Can you post some pics of the strut gap your referencing?

I’m not sure a 2007 has EGR, I don’t think it does. With VVT, emissions can be managed by Changing valve timing. I thought both SAS and EGR died with VVT in the late P80 era I think your right about secondary air system and EGR system's for non diesel but what about the PCV systems on a 2007 XC70? ...

FCPEURO.COM sells everything for Volvo practically and they have a "Lifetime Warranty " on everything they sell and they cover the warranty themselves. I purchased a Bosch Fuel Pump Assembly (assembly comes with everything, not just the actual pump itself), Bosch is the "factory Genuine Volvo " fuel...

I have performed the test with the key in position 2 and disconnecting the battery negative suggested by dwwalker. Watch me do this test and the Schrader valve test in the video below. https://youtu.be/u6W1JRF4AOU The test did not make any difference in my case. The car still does not start in cold...

Check your EGR system, if your EGR system is really bad it's full of resin/carbon that will expand during extreme weather conditions. This could possibly block passage ways and it's rare but I've seen a no start condition in extreme cold weather because of this issue. I actually heated up the area w...

I love my Volvo & bought it in 1981. I am the second owner and have maintained it extremely well. My car works in many television shows and I'm very proud of my 1979 Volvo. I've always been a believer if something works well, keep it! Why feel the need to replace it. Nothing's made in life nowadays...

[quote=MoVolvos post_id=530429 Did you get a set of FCS Quick Strut Assemblies? I almost ordered the FCS Front Struts for the 08 C30. I did some research and almost purchased it because of the Lifetime Warranty but would prefer to go through the manufacturer. Unfortunately, you have to go through CA...

Three years later, any closure .. for absolute certain ? I have very similar problems resulting in ''reduced engine performance" No power above 1500 rpm ! Also still no engine cooling fan activity , but I do not THINK its overheating ! . 2003 Volvo S60, T, 5, AWD, 140K Have you scanned your ECM for...

bobice wrote: ↑Mon Nov 11, 2013 8:58 pm Thanks! I bought the Volvo rear differential oil from FCPeuro, mineral based for $19. Will try and see whether the fluid change will help.

It must have a slow leak if it was low...did it resolve your issue?

I love my Volvo & bought it in 1981. I am the second owner and have maintained it extremely well. My car works in many television shows and I'm very proud of my 1979 Volvo. I've always been a believer if something works well, keep it! Why feel the need to replace it. Nothing's made in life nowadays...

I ordered the FCS after reading a lot of positive reviews. I'm doing the front Macpherson strut assemblies, (Moog)sway bar links and (Moog)tie rod ends. The Macpherson strut assemblies look well made, came with new hardware and the ABS clip was actually included. I kept the Genuine Volvo Strut Assem...

I have the Zimmerman rotors with Z coat on all 4 plus bosch ceramic Quiet on all 4 on my 2005 Saab 9-2x and I really like the rotors, they don't seem to ever have surface rust.

The newer Sachs struts have a rubber lower spring seat which makes the front units much quieter. I couldn't believe the difference in sound suppression when we ordered just the Sachs struts and received lower spring seats for a customer's 2007 vehicle. Unless FCS are supplying these with lower seat...

I don't know about FCS... I installed Bilstein strut and wrote a DIY in this forum... Thank you. Bilsteins are excellent, I've installed there coil springs on other vehicles with Sachs Struts and Bilstein struts. I'm really curious about this FCS Company though. Made in America...I like the sound o...

My wife's 2004 XC90 T6 front struts are squeaking and I'm ready to swap in some new struts. Normally I go with Sachs on all of my Volvo's over the years. Our 2004 XC70 has brand new Sachs all around with Lemfordor Coil Springs in the back and Sachs quick Struts up front. I was going to purchase Sach...

abscate wrote: ↑Wed Dec 04, 2019 10:59 am Maybe a new user name?

Bambi_Killer looks free...

(do remember in NYS that deer hits are comprehensive claim - for the win.)

That's terrible...lol. I work very early in the morning and do a bunch of driving, this is when deer are looking for breakfast.

The master cylinders on Volvo’s seem to last forever. We have so few replacements documented here compared to other makes I’m familiar with. Normally I'd agree but since most vehicle owners don't do PM's, especially brake fluid service intervals. Example: About 6 months ago a customer of mine broug...

cn90 wrote: ↑Mon Nov 25, 2019 7:59 pm Maybe it is bad Master Cylinder...

+1

Anyone? You can fix it yourself but a Volvo dealership charges atleast $135.00 an hour. The ABS sensor doesn't make sense to me though. For the drainage issues you should remove some of the trim on that side to pull up carpet in front footwell. The get someone to pour water down the drains and watc...

I've debated this same topic in my head numerous times. I'm really feeling the look of the P3 XC70 T6 specifically. I love the look of the P80 chassis V70XC's and the P2 XC70/XC70R with AWD. I've owned 3 P80 chassis V70XC's and loved all of them. Presently own the 2004 P2 XC70 w/factory HID's, the B...

I've had 2 more deer run into this since initially posting this, I need a force field out here.

Osram is the factory company, Osram is Sylvania but you spend less $$ buying Xenon items in an Osram box instead a Sylvania box or even more expensive in a Volvo box... all the same quality product. I own a 2004 XC70 with factory HID/Xenon lighting.

I replaced the factory purge valve along with some of the EVAP line by the IM. This is the second time I'm replacing the purge valve on this vehicle, 2004 XC70. Fortunately I purchased the first one from FCPEURO.COM, so replacements are covered for life.

Sachs now offer quick struts, all factory parts in a quick Macpherson strut. There top quality. FCPEURO.COM offers with lifetime warranty. $250.00 for 2004 XC70 front Macpherson.

Go to another shop, there charging twice for same labor.

I have Lesjofors springs in my BMWs. Great springs, probably OEM supplier, for the $. I already installed a new set of Lesjofors with a new set of Sachs in the rear of our 2004 XC70. The ride height is great and drives nicely in the rear. I just had to replace another broken spring up front thought...

I guess I’ll find out if the leaks stop tomorrow and change the oil. The color of the oil is still newish. I know the oil cap says castrol on it. Is Castrol the best choice for a car with 175k? I think the other seals are good but I’ll find out once the lock rings are removed. There’s no splash gua...

Fuel leaks are sometimes the orings at sending unit or fuel pump. Just replaced oring on sending unit for my wife XC90 T6 9 Months ago. You can replace the access covers, I believe FCPEURO.COM has them but you must pull the actual fuel pump and sending unit to check orings if there making air tight ...

It's probably too late, but I was in the same situation/dilemma & ultimately opted for the "reinforced" or heavy duty version of the Lesjofors springs. There's literally almost zero documentation on them, unless you look at some of the European sites that require translation. They are most definite...

Broken springs is common on XC70. Very rare on any other P2 model, S60 V70 XC90 or S80 My wild guess is some Volvo engineer just took the spring data from the S60 and added some length without properly calculating an additional area section, resulting in a weak spring for the XC70. Just a guess of ...

Which springs are your u muching up Shiloh? I’m on my third set on the E83 but’s the only broken one Ive had on a Volvo was broken my PO The original springs on 3, 2 front one rear. 2 new ones from FCP, Nordic was the manufacturer and was considered OEM, I paired them with Sachs struts, Volvo mount...

Just ran out to my car to do the glove test and it sucked it right in, so no issues there with the PVC. Do the front cam seals leak due to things other than the PVC? Since your front cam seals are already leaking the glove test might not be 100% accurate, some pressure would escape at the cam seals...

Our 2004 XC70 has another broken coil spring but this time it's in the rear, R/R. I've replaced 3 coil springs up front over the last 3 years. I must admit that I'm quite disappointed in either the quality or engineering decision with the XC70 version of the V70 chassis. The XC70 slhas about 4 inche...

I replaced the heater hoses finally, I had to cut one if them 2 years ago because it was leaking the clamp. This time there was 2 pin holes and I dont feel like removing them again so I ordered both of them (Blue Box) from FCP. The sad part is after the installation was completed I went for a test d...

Also read good reviews about Lesjofors. In fact, I think remember they make the springs for Volvo for the P2 platform. Anyhow, the longer OEM springs on XC70 are known to fail now and then. Much less on the S60 or XC90 I'm glad to hear that you read good reviews on the Lesjofors. Our XC90 has been ...

My R/R coil spring just broke, so I've replaced each front spring twice and now the R/R is getting replaced. I just purchased 2 Lesjofors from FCPEURO.COM for about $70 a piece. After researching the Lesjofors company(150 years of experience) and reading customer reviews I decided to make the purcha...

[quote=natural4reelz post_id=501029 time=1553204693 user_id=99447] Heres a pic of what looks like metal around some rubber things that its Says “This is for the oil filter housing ... I was told i have a oil leak under my csr and the said my oil filter housing and cap is cracked bad ... So di i need...

20190321_155229.jpg My wife's 2004 XC70 just had a split rubber coolant hose on the PCV Crankcase ventilation/coolant pipe(30731068). The rubber portion of this setup was replaceable, so I replaced just the rubber hose. Just curious how many miles in your 2004 XC70 when the "rubber portion" of PN 3...

Clearing any diagnostic trouble code doesn't resolve the issue and believe me when I say that I wish it was this easy.

: 20190304_103534_fixed.jpg (99.69 KiB) Viewed 1836 times

There is all 3 of mine and looking to add a c30R sometime soon.

Throwing money at problems rarely fixes anything properly, example; our government throws money at problems and rarely does this resolve issues properly. Unfortunately if your automotivly illiterate you will get ripped off time and time again. I would first try a drain and fill a couple times even i...

xHeart wrote: ↑Sat Dec 01, 2018 10:46 am Diagram showing coolant pipes and fittings behind the block -- water pump, turbo cooling, and thermostat.

It's not in this diagram, its parts of that pcv pn # listed.

Interesting. Is the wire correctly attached to the strut plastic (or metal) bracket? Speaking of these sensors, careful not to pull on the wire (even just slightly) when removing a sensor or working on the suspension, always pry out the sensor with a flat screwdriver from underneath. Yes the wire g...

My ABS icon lit up other day and the Anti skid light flashes briefly like tires were spinning but they weren't. I pulled the ABS codes with my handheld and got ABS 0011- Front left wheel speed sensor fault. After pulling that wheel off I found this, 20190208_105555.jpg 20190208_105608.jpg I guess it...

20190205_141847.jpg It wouldn't make sense to go through all this trouble removing the middle row of seats and skip replacing the o-ring. The plastic tank uses a green o-ring and the metal tank uses a black o-ring. I used my VIN # to order mine directly from Volvo because I wanted it ASAP but you c...

lightphonics wrote: ↑Mon Feb 04, 2019 11:52 am Update:
After 5 days with no codes being pulled, I finally got a P0336 code today. Crankshaft position sensor is the suspect!

I'd take timing belt cover off and check everything.

That sheds some light on matters. From the factory, I have never heard of either side leaking while the car is young. After years of use the plastic top will fail and leak. After replacement I have heard many stories of people messing up the o-ring seal - which may be what you have. If that is the ...

Good find. How bad does it smell in the car? Generally on Volvos of this era the fuel pump is the culprit. The plastic on top gets brittle and starts to crack with age and time. It would make sense the sending unit side would do the same thing. Some people fix the problem by "pooling" a thin layer ...

I found fuel pooled up on top of sending unit.
So I ordered new seal, lock ring and sending unit.

If you were to get the Volvo branded bulbs ($45 ea.) here: https://www.fcpeuro.com/products/volvo-hid-headlight-bulb-genuine-989833 They have a lifetime warranty on all of their parts and I know firsthand that they honor the warranty. Seems like a good deal. Fcpeuro.com is probably the best EDM veh...

www.powerbulbs.com Osram Xenarc Cool Blue Intense D2R. $59.39 USD Osram is Sylvania in USD, WWW.powerbulbs.com is in GB I believe. These bulb are 6000k . You have to be careful buying Osram, Phillips, Sylvania stuff because people are selling knock offs, my bulbs actually came with special stickers ...

2004 XC90 T6 , leaking from passenger side right by front of tank, looks like its rolling from top or side of tank. What's on that side, sending unit?

Check front brakes, if caliper pins are sticking that could cause serious vibration if just one pin is sticking. Does the vibration get worse upon acceleration or braking?

abscate wrote: ↑Wed Jan 30, 2019 5:33 am That jack is just a safety, right Russ?

( safety Nazi abscate)

I don't get it. ??
It's under the frame, but I have a jack stand at jack stand location.

: 2004 USDM XC70 Bi-Xenon headlight

Our P2 Cross Country is a bit dirty from salt on the road but here's my actual USDM Bi-Xenon headlight.
I must admit that I'm a bit bummed out after finding out that the EDM Xenon headlights have a separate high beam just like the Halogen .

20190127_161933.jpg 20190127_161938.jpg 20190127_150552.jpg 20190127_150545.jpg Completed brake job yesterday, I initially started with 4 Zimmermann rotors, 8 Akebono ceramic brake pads, 2 set screws for rotors and 2 front brake lines(soft). I had finished the back brakes a few weeks ago and finall...

abscate wrote: ↑Mon Jan 28, 2019 3:10 pm Pay FCP once.....cry....and only cry once.

+1

20181107_183925.jpg 20181107_161556.jpg I've had the factory springs break and an OEM set of front springs break on our 04 XC70. I finally bought Bilstein springs. I had replaced everything up front...Sachs struts, factory strut mounts, cross nut, strut nut, bump stops from FCPEURO. Only thing that...

I'm thinking throttle body issue or atleast throttle body issue was my first thought after initially ready this thread. After reading the next 3 pages of post I'm still thinking throttle body issue.

The exhaust gases would have to get really hot to make the turbo charger glow cherry red!!

This thread topic is exactly what I thought upon first symptoms. A month ago my 2004 XC70 felt like the R/F CV halfshaft popped out of transfer case then back in. The noise it made was distinctively the splines being stripped down some because there was play, hence the snout of the inner part of dri...

Unplug them and see what happens.

If the service history of said vehicle is unknown then a fluid flush is usually taken off the table. Draining the old fluid by way of pan drain plug is fine. If your already experiencing issues with shifting then doing nothing can only lead to failure . I'd do a few drain and fills over the next few...

I'm going to piggyback what a abscate suggested, I've actually experienced this in the past on one of my 4 V70XC's that I use to own. I had visually inspected all turbo induction hoses but the tear was in an area that couldn't be seen without removing the tube. The symptoms you mentioned were identi...

This is a European headlight in action. First the parking light (not legal while driving in Sweden, it's for use when parked with car off). Then low beam 35w xenon. Then high beam 35+55w xenon, originally the last 55w was halogen. There is really no point using the 0 on Euro spec cars. The entire d...

: md_f5ddc0f2-5370-4280-8fca-0eadb96711e7.jpg (12.5 KiB) Viewed 213 times

This is the usdm version in my 2004 XC70. The inner round light only activates in the daytime if you have switch set to 0 , otherwise the low beam xenons stay illuminated at the 12 o'clock position on the switch.

I'll be darned. I managed to find a reference to auto DRL at least for the S80. That's not on my car at least. It's always on. Not that if want it any other way. However if that means the second high beam bulb is gone I stand by my previous statement that they've crippled the headlights by removing...

New to the group here. New to the XC70 as well. 2004. I am a bit confused by the DRL's and the high beams and think I might have an issue with one or both. High beams first. I switch them on with the stalk (yes i have the headlight switch at 12:00) and the only thing that happens is my low beams (H...

New to the group here. New to the XC70 as well. 2004. I am a bit confused by the DRL's and the high beams and think I might have an issue with one or both. High beams first. I switch them on with the stalk (yes i have the headlight switch at 12:00) and the only thing that happens is my low beams (H...

I never really tried to count how many Volvo vehicles I see e everyday but I see 3 everyday in my backyard parking area. But I do see the Cross Country models quite frequently (XC70 p2/p3, V70XC/V70 p80, Xc90, XC60).

How long have you been using the type 4 in your 4T65? I am really curious about any difference in shifting etc. As stated I own and drive daily a 2004 S80 T6 which is essentially your cars sister. Above is my experience with the dealer installed new Volvo 4T65 (like your car) and non standard Dextro...

My 2004 XC70 is getting new brake rotors, pads at all 4 corners and new rubber brake lines up front. I really didn't want to try to cut rotors again since these brake rotors are really old and abused. I opted for "Zimmerman " brake rotors since Ive been wanting to try this brand. I'm using premium c...

The 2004 T6 transmission requires Dextron III fluid. There is genuine Volvo Dextron fluid. I would not put non Dextron in your T6. It has a 4T65 GM transmission. June June I appreciate your feedback always. Yes you are correct that DeX 3 is what's called for but T-IV exceeds dex3 and is compatible....

We love our 2004 Volvo XC90 T6 for many reasons. My opinion on Volvo in general is biased because I'm a Volvo Enthusiast and I've always wanted an XC90 T6 since they came onto the market. The T6 is obviously much nicer than the T5, bigger engine, twin turbocharged inline 6, bigger wheels, bigger br...

We love our 2004 Volvo XC90 T6 for many reasons. My opinion on Volvo in general is biased because I'm a Volvo Enthusiast and I've always wanted an XC90 T6 since they came onto the market. The T6 is obviously much nicer than the T5, bigger engine, twin turbocharged inline 6, bigger wheels, bigger bra...

I was able to get some more information concerning AWD issue. E000- Control module Communication faulty Communication. 0065- Stop (brake) lamp switch signal outside range. 0103-Pedal Position sensor faulty signal. 0147- Pedal Position sensor signal outside its permitted range. So it looks like somet...

I thought there was a fuse in the fuse block just for the actual audible siren on the P2 chassis.

The AOC AWD system is not active without engine running. The hydraulic pump is not turned on until the engine running data bit is broadcast on network. If you do the same things with eng running and you do not have considerable effort to turn the wheel then there is a problem. The AOC will have a l...

boostedxc wrote: ↑Thu Dec 27, 2018 11:27 am I have a controller from a 04 v70

You think I need one?

The AOC AWD system is not active without engine running. The hydraulic pump is not turned on until the engine running data bit is broadcast on network. If you do the same things with eng running and you do not have considerable effort to turn the wheel then there is a problem. The AOC will have a l...

That's not a lot to go on. Best to scan with Vida. If DEM (AWD controller at rear axle) is offline the CEL isn't lit in any case. If the hydraulic pump has failed the result is the same as a failed DEM. There are AWD tests you can perform. It's best to search here for the actual operational tests f...

Yesterday I was replacing brake rotors and pads on our 2004 XC70. I do one corner at a time and realized that both rear wheels could spin freely. I did notice recently that my front wheels would freak loose quite easily on gravel but didn't put it together. I hear no noises and have no CEL Edit; I s...

Won't a 02 5cyl have the 5 speed transmission that takes special fluid? Something like 3309 or equal? Have read so much on here about Toyota I think type 4 is supposed to be the cheapest? Would the Royal Purple be equivalent to the 3309? Guys please chime in as my Volvo uses Dextron III as with all...

Using the proper spark plug is important, as mentioned previously you won't gain any HP but you could actually lose some HP using improper plugs. Volvo vehicles notoriously reject aftermarket plugs but to each there own. I'm a true believer in using factory parts, especially something as cheap as sp...

My 2004 XC70 was having issue with brake booster/brake pedal sensor. About 2 years ago I replaced this sensor with a "Pro Parts Sweden" brake pedal sensor. The PPS worked but obviously failed in less than 2 years because of the silicone they used on the bottom was crumbling off. This time I purchase...

Thanks much, As I mentioned it's intermittent . and yes when I drive at night I can usually tell when Hi beams are on, in this case I have to hold the lever when the issue is present. And I suspect a weird ground short some-where as well. It's a tad cold to go looking for it, so I suspect I'll just...

The "reduced engine performance " message usually is in relation to brake booster system ...maybe brake pedal sensor(also power booster sensor) or booster vacuum switch or hoses to and from vacuum switch. Factory codes. That is interesting info. I got my Bluetooth scanner yesterday and installed th...

Sounds like you dash cluster needs to be replaced possibly but obviously you need to check out wiring back of cluster to power source/ground. Have you verified that high beam aren't physically working? I mean get out the car and check, just because high beam icon isn't illuminated on dash doesn't me...

Thanks, I have a scanner coming from Amazon Thursday. I will report back my findings then. The "reduced engine performance " message usually is in relation to brake booster system ...maybe brake pedal sensor(also power booster sensor) or booster vacuum switch or hoses to and from vacuum switch. Fac...

My wife's 2004 XC70 just had a split rubber coolant hose on the PCV Crankcase ventilation/coolant pipe(30731068). The rubber portion of this setup was replaceable, so I replaced just the rubber hose. Just curious how many miles in your 2004 XC70 when the "rubber portion" of PN 30731068 split? Also,...

Car is an '04 V70 with 130K miles. I drove the car last week from Nashville to Ft. Lauderdale (850 miles) with zero problems. Car has clean oil and has been well maintained, with no warning messages/indicators turned on until it started acting up today. About 5-10 minutes into my drive to lunch, th...

Fcpeuro.com has a good price on Bosch(factory manufacturer) with lifetime warranty, so if they go bad free replacement. Cant be at that.

If your going to remove sprocket hubs, get rear camshaft/crankshaft locking tools.

This is a good topic, I've been through this personally with our 2004 XC70 w/factory Xenon/Bi-xenon lighting. After hurricane Sandy the R/F Ballast module and the ignitor failed. So I had to repair the headlight because a new factory assembly was like $1100.00. We love the lighting but it's expensiv...

On a 2002 V70 X/C, 2.4L turbo, does the intake cam use a seal on the rear? I saw one on the rear of the exhaust cam, but not the intake. I have a 2004 XC70 and both exhaust/intake cam have same rear cam seals. But I believe in 2003 they changed a few things. Firstly my 2004 is a 2.5l , I also have ...

This is more for future people who may come across this conversation.. The problem with most 'heavy duty' springs, which are usually aftermarket, is that generally they're designed to facilitate a heavier cargo load. Which can be confused with the concept of longevity. They will make the car sit a ...

20181107_183942.jpg 20181107_183952.jpg So this is the F/R strut with a new Febi Bilstein coil spring. I figured I would try a different brand this time, Bilstein is very well known for excellent suspension parts whether factory spec or high performance. I've seen springs break but 3 broken springs...

Strapping to the control arms is still no different than driving up a steep incline as far as the stresses on the spring are concerned. It's the same forces whether applied via a strap around the control arm or by engine power at the wheel. I've seen two coil springs break over the years on differe...

Very nice purchase. Welcome aboard!!

I don't quite understand how the lateral force presented to the coil spring by a tow truck would be different than the same stresses that you would see normally through stomping on the gas or braking hard. The tow truck grabs onto the wheel, not the spring. I'm thinking that would have broke soon w...

abscate wrote: ↑Fri Nov 09, 2018 5:17 am They probably caught a strap or chain in the spring when they locked it up. Not really something one can prove.

Yes sir!! They used straps because the P2 doesn't have frame towing hooks. P2 has crappy eye hooks that screw into the bumpers.

- How many miles? - Maybe that spring is rusted and was about to go south anyway, I don't think the shop did it. It is NOT easy to break a spring. They were factory springs that I purchased from fcp not even 2 years ago. I bought new Sachs struts, strut mounts and everything else all factory or bet...

We love our 2004 Volvo XC70, it has 225k on the odometer and running strong. We originally purchased her 5-6 years ago for $4500 w/125k (I believe) on odometer. When we purchased her she had the Timing Belt Service with Water pump, tensioner and idle pulley replaced also. All 4 struts were replaced ...

Momtreal wrote: ↑Wed Nov 07, 2018 9:59 am My car sounds like it is an airplane, which is really cool to my kids but the joke is on me.

Just wondering what the causes could be before heading in to the garage, Can I disconnect, Do I need the turbo>?

Any chance of posting a video clip with sound?

20181107_151557.jpg 20181107_151738.jpg 20181107_161601.jpg 20181107_183925.jpg So a month ago a pcv system coolant line split at the clamping location. I had it towed home to repair because it required removal of airbox, MAF to Turbo tube, upper engine torque mount, upper strut brace. Somehow this...

Haha oh man, I'm getting pretty good at doing that. I have the cover off right now. The original cover was left at the JY months ago. I'm thinking at this point my best and cheapest option will be to grab another head from the yard off a turbo car and keep everything the same as it was in the car I...

Engine sounds fine. Pcv has been done. Plugs are good. Oil fill cap is not bad accept i need new one cause seal is cracking. Thanx for the ideas. Have you tried taking the temperature of top half of motor with infrared laser thermometer? This way you can get an exact location of area that's over he...

I know you stated that issue was resolved but since the "bevel gear" was mentioned, now might be a good time to service that bevel gear with some new oil. Good way to avoid that from howling, much cheaper also. Another overlooked item would be the rear differential and ATF service.

I was going to suggest checking the plumbing at the turbo flanges, over time the constant heat kills the plumbing where the tubes mate to the turbo flange and even though it make look fine you actually have to remove that air duct to see behind the clamps. But your MAF sensor sounds problematic.

Do you have xenon lighting or halogen? If its xenon it could be the ballast or ignitor or headlight module.

Dont go aftermarket on a structure piece, accept used if not new Volvo. After all you want the correct accident performance in the future. Looks like the car did it's job protecting you. June Thank you for your response June. Yes Volvo does great protecting passengers of there vehicles, that's one ...

I think you're talking about two different things. I thought TS wanted to fit one of these, not replace the internal front collision bar with an aftermarket option. These are common over here with a lot of different options and manufacturers having XC90 specific models. Not sure about how well they...

I agree with June - you bought the car for safety don't put an aftermarket part that is crash/structure related. Were it me I would buy everything used. Search the wreckers and Craigslist and buy a used hood of the same color. If the part is bolted on buy a used part (I think the radiator support m...

Dont go aftermarket on a structure piece, accept used if not new Volvo. After all you want the correct accident performance in the future. Looks like the car did it's job protecting you. June Thank you for your response June. Yes Volvo does great protecting passengers of there vehicles, that's one ...

So after 3 weeks of owning our beautiful 2004 XC90 T6 a pack of deer run out of hedges and in front of me. I was only going about 30mph but the deer was also running about 30mph, so bam!! It doesn't look so bad and still driveable but it's just over $3k worth of damage. The radiator support is bent ...

Can absolutely be a thread extension for new owners, it's what the forums are all about. I'll hope that you've read up on the T6 and the 4T65EV/GT 4-speed transmission. Any idea if this is the original transmission? To answer your question; I went through all the paperwork again, the Transmission, ...

I believe there's 2 relays in the rear fuse block associated with the brake lights.

I use Aisin Warner OT4 for all 4 of our Cross County's, Aisin Warner is a large manufacturer of Automatic Transmissions. I believe Aisin Warner transmissions are used on many Volvo models. I also believe that Aisin Warner is the ATF in the Toyota Type IV bottles, regardless it has worked well for my...

Did you clear all codes and re-check them? MAF and ETM faults sound the most critical. If they don’t go away after resets and re-cranking, they need to be addressed first. I believe 02 is last year of the faulty ETM design. If you clean it, reset codes and then still have fault, you are going to ha...

P2111 probably means time for new electronic throttle body module. It would have to be really gunked up to cause throttle actuator to stick open or closed.

You have a lot of issues, try unplugging the MAF connector from the MAF sensor. Its connected to air filter box under your hood. Then try to start her up and see if she'll run better. Also check all of the turbo plumbing, if anything is disconnected or has a hole or rip it can cause your described s...

I just purchased a new tube for my wife's 2004 xc70. Hers broke off at the turbo flange.
I bought if from fcpeuro for around $100, I'd rather not worry about it opose to rigging it up.

I just purchased a new tube for my wife's 2004 xc70. Hers broke off at the turbo flange.
I bought if from fcpeuro for around $100, I'd rather not worry about than rigg it up.

Sounds like a lot of work, I'm sure it looks great. Sure glad my wife's 2004 has the glass bi-xenon lens. Unfortunately my new to me 2004 XC90 has plastic lens and I'm thinking of purchasing new depo's.. I believe they make the factory lens for the 2004 XC90 T6. The good thing about the XC90 though ...

The glass lens outlast these new plastic lens by far, my 2004 has 225k on the odometer with plenty of night driving and the glass lens are still crystal clear. The plastic lens on the 2005's glaze over after 5-6 years unless consistently buffed out and polished.
I'll stay with the glass...

For spark plugs I've bought Volvo brand for almost same price as the original equipment manufacturer. FCPEURO.COM.. But I've been accused of being very picky with my Volvo's. Look on the coil packs/ignition coils that your XC90 R has in the car now and they to find the brand name written on the actu...

Best fix for glazed over plastic headlight lens is set of glass lens. My 2004 XC70 has glass lens with bi-xenon low/high beam and separate day running beam.

I believe it can be seen here sitting next to my 1998 V70XC.

Hello, I just bought a 09 Xc90 3.2 r design with 95,000 on it. Should I change the spark plugs and ignition coils? I’m not sure what else is involved in a tune up on these? Thank you The spark plugs are cheap enough but the ignition coils a little bit more money but I'd say yes if the ignition coil...

My wife's 2004 XC70 just had a split rubber coolant hose on the PCV Crankcase ventilation/coolant pipe(30731068). The rubber portion of this setup was replaceable, so I replaced just the rubber hose.

For a grand you can't go wrong if you get a year out of it, if the trans last longer you got a great deal. Exterior looks great in pics.

This topic makes me very nervous as I just purchased a 2004 XC90 T6. I'm not new to Volvo by any means but I've never heard that the T6 had issues with Transmission that was very serious or common. But if you get get 100k out of a trans that's unusual for my experience having owned 6 volvos. The Xc9...

Can absolutely be a thread extension for new owners, it's what the forums are all about. I'll hope that you've read up on the T6 and the 4T65EV/GT 4-speed transmission. Any idea if this is the original transmission? I've heard that they are a weak point and I knew someone who had issues with the tc...

cn90 wrote: ↑Thu Sep 20, 2018 9:41 am Just curious how many miles in your XC70 when the PCV coolant hose burst...

225k

I have an '04 XC70 and '04 XC90, from my recollection I would say yes they look identical. Sounds like a great swap for better stability around corners and on /off ramps. I'd like to hear how the rear sway bar from a V70R works out after you swap it in.

Crap on rye. Two weeks after the event, the tow truck guy has probably already left for another job. Take pix, showing fresh damage, maybe you can get some love from them? If it was a AAA tow that is a plus Very funny. Worst case scenario fcpeuro does warranty there parts for life, I mean as uncomm...

Home Depot has a good section for electrical supplies, I bought wiring loom for harnesses, 3M electrical tape, pull ties. The wiring loom can be bought in a variety of sizes.

Our 2004 XC70 busted the coolant rubber hose on the crankcase ventilation coolant pipe. Since I didn't want to change it on spot I had it towed home. Tow driver had to place on flatbed pulling rear of car up first and he used straps because the eyehooks wouldn't catch threading in back location. We ...

I think the reason is the PCV piping is plastic and eventually gets brittle and fails from hot oil exposure. I barely torqued mine and I felt the plastic shatter inside the insulation. If it is intact, though, I agree its a $200 part you don't need. I probably would have splurged for this crankcase...

You can re-use the metal cover gaskets. I would work on it by blowing with compressed air and then clean with throttle/brake cleaner then blow it dry. Use the epoxy and see how it goes. Sounds like just the cost of the epoxy to me! With the fuel pump there is another connector out of picture which ...

- How many miles on your XC70? - For the rubber hose: cut the factory Oetiker clamp, install new hose, install new clamps. That is it. - This design is convoluted and serves no purposes. The hot coolant cannot even warm the PCV pipe enough to prevent mayo build-up. Just funky engineering. PS: Also,...

Be really careful with that PCV coolant line because the vapour part is plastic and will crack easily. Put new washers in the banjo fitting and have fun. I'm actually only replacing the rubber line, not even breaking the seal on the banjo bolt. Napa was actually able to find me the right hose with ...

My wife's 2004 XC70 has had the slowest leak for a while and I never really located it. So a week ago it turned into a major leak and had to tow home since it wouldn't hold coolant long to get her home. Anyway after digging into drivers side of motor I finally found a hose attached to a hard line th...

Hi All, I own a 2007 XC-90 with a progressive electrical issue. Originally the front cigarette lighter, DVD player, and front passenger seat stopped working around the same time. Now the AC fan stops working (blowing) as well. I've checked all known fuses and seem to be in good order. The battery w...

Wow I f'd up, I never to meant to try to highjack this thread...I thought it was a thread for new Volvo XC90 owners. My apologies to the thread starter.

23782.jpeg lI'm not new to Volvo or MVS, I just added a 2004 XC90 T6 to my Volvo collection. 1owner, certified Volvo w/all maintenance and repairs completed at Ramsey Volvo in NJ. Every recommended maintenance item was completed as per manufacturer recommendations (ATF services, differential servic...

MDK'S 1998 XC70 . they ask.. how many parts are you gonna bolt on that thing?... I don't know... the latest are a set S 60 AWD Wheels with 215 45 17's ... I got them with tires off of Craigslist for 200$ ...with Bridgestones ...no less. Volvo in latin is... I roll.., rolling on! Those wheels just l...

Search found 0 matches