Had a weird occurrence happen yesterday. While driving, I lost all info from the DIM and a lot of other electrics were not working (driver side window switches, turn signals, inside lights...) no maintenance has been done for months. Got home, restarted the car and everything returned to normal except now I have an SRS warning displayed on the DIM which I cannot reset with my scan tool.
Checked for codes and found none.
I presume that I am going to have to get the SRS warning reset by someone with a better tool.
Anyone have any ideas?
SRS warning on 2002 V70 242 K miles
- Krons
- Posts: 1073
- Joined: 9 January 2022
- Year and Model: 08S60 05XC90 02S60
- Location: Des Moines, IA
- Has thanked: 193 times
- Been thanked: 202 times
A few services on eBay that’ll reset them.
08 S602.5T/05 XC902.5T/02 S602.4T
08 C702.5T (sold)
05 S402.4i (RIP, timing belt failure)
The non-Swedes:
25 Mazda MX-5 / 17 Frontier Pro-4X / 17 Ford Focus
17 R1200GS / 15 Versys 1000 / 11 DR-Z400S / 07 R1200GSA
08 C702.5T (sold)
05 S402.4i (RIP, timing belt failure)
The non-Swedes:
25 Mazda MX-5 / 17 Frontier Pro-4X / 17 Ford Focus
17 R1200GS / 15 Versys 1000 / 11 DR-Z400S / 07 R1200GSA
- MoVolvos
- Posts: 5273
- Joined: 15 January 2012
- Year and Model: S&V70XC,S60,C30,XC90
- Location: NC
- Has thanked: 310 times
- Been thanked: 524 times
.ljsommar1 wrote: ↑24 Jan 2024, 13:01 Had a weird occurrence happen yesterday. While driving, I lost all info from the DIM and a lot of other electrics were not working (driver side window switches, turn signals, inside lights...) no maintenance has been done for months. Got home, restarted the car and everything returned to normal except now I have an SRS warning displayed on the DIM which I cannot reset with my scan tool.
Checked for codes and found none.
I presume that I am going to have to get the SRS warning reset by someone with a better tool.
Anyone have any ideas?
Same intermittent Gremlin on a 2002 V70 XC with 88K miles. If I tap the dash or DIM some of the functions will return but go out again. I believe the DIM will require solder work. Not sure about the others yet.
.
https://www.youtube.com/results?search_ ... dim+repair+
.
.
Blessings,
BKM
2008 C30 T5 2.0 M66
2007 S60 2.5T - New Project
2003 S80 T6 Transmission DIED
2000 S70 SE Base - New Project
1998 S70 T5 Prior
1989 240 Wagon Prior
BKM
2008 C30 T5 2.0 M66
2007 S60 2.5T - New Project
2003 S80 T6 Transmission DIED
2000 S70 SE Base - New Project
1998 S70 T5 Prior
1989 240 Wagon Prior
- jonesg
- Posts: 3507
- Joined: 16 January 2008
- Year and Model: 2004 V70
- Location: Northern maine.
- Has thanked: 69 times
- Been thanked: 481 times
fix the cause first, try a wiggle test on the connectors to the dash pc board.ljsommar1 wrote: ↑24 Jan 2024, 13:01 Had a weird occurrence happen yesterday. While driving, I lost all info from the DIM and a lot of other electrics were not working (driver side window switches, turn signals, inside lights...) no maintenance has been done for months. Got home, restarted the car and everything returned to normal except now I have an SRS warning displayed on the DIM which I cannot reset with my scan tool.
Checked for codes and found none.
I presume that I am going to have to get the SRS warning reset by someone with a better tool.
Anyone have any ideas?
if you pay to clear the srs it will come back when the fault repeats and you'll be out the money.
I would get a vida set up before paying to have codes cleared.
- ljsommar1
- Posts: 92
- Joined: 18 July 2019
- Year and Model: 2002V70
- Location: Pennsylvania
- Been thanked: 8 times
Well, no problems reappeared after multiple trips. So, I got the SRS warning reset. It cost me $30 plus tax which was not too bad I think.
He did a full scan and no other problems showed except it says wrong software for the drivers front seat module which my scan tool also showed. I suppose that happened when I took the seat out to bolster up the worn out bottom. The control for that seat only works for about 30 seconds after I put the key in position 2. I would guess it probably lost all its software. I can live with it , I never change seat position anyway.
He did a full scan and no other problems showed except it says wrong software for the drivers front seat module which my scan tool also showed. I suppose that happened when I took the seat out to bolster up the worn out bottom. The control for that seat only works for about 30 seconds after I put the key in position 2. I would guess it probably lost all its software. I can live with it , I never change seat position anyway.
-
- Similar Topics
- Replies
- Views
- Last post






