Login Register

SRS control module replacement

Help, Advice, Owners' Discussion and DIY Tutorials devoted to the second generation C70, S40 and V50 Volvos -- awkwardly model year 2004 ½ onwards -- plus where to go for advice and discussion on Volvo's sporty C30 Coupe powered by Volvo's ubiquitous inline 5-cylinder power plant.
Post Reply
dylan_iker
Posts: 6
Joined: 2 December 2015
Year and Model: 2008 s40 r design
Location: coventry

SRS control module replacement

Post by dylan_iker »

hello. i have an s40 2008 r design and my srs service urgent msg is showing up and ut cannot be cleared.
Now im thinking of replacing the module with the one i found at the volvo breakers. The part numbers are the same, so will it need to be programmed and also, will be msg go away or it needs to be cleared?

doublebug
Posts: 347
Joined: 19 July 2013
Year and Model: XC90 2007 D5
Location: Belarus
Been thanked: 7 times

Post by doublebug »

If donor is from the same car (the same MY same model and same configuration of SRS system it wont need to be programmed)
If you have questions about Volvo firmware ask me. I may know an answer :)

doublebug
Posts: 347
Joined: 19 July 2013
Year and Model: XC90 2007 D5
Location: Belarus
Been thanked: 7 times

Post by doublebug »

Plus if you have DiCE I can do software transfer from old module to the new one.
Or just clear these unerasable errors.
If you have questions about Volvo firmware ask me. I may know an answer :)

dylan_iker
Posts: 6
Joined: 2 December 2015
Year and Model: 2008 s40 r design
Location: coventry

Post by dylan_iker »

wen i plug the second had part, will the light continue to show and will it need to be cleared or there wont be any lights

doublebug
Posts: 347
Joined: 19 July 2013
Year and Model: XC90 2007 D5
Location: Belarus
Been thanked: 7 times

Post by doublebug »

If the new module and software fits your car and this module does not have any error codes stored the message should go away.
If you have questions about Volvo firmware ask me. I may know an answer :)

dylan_iker
Posts: 6
Joined: 2 December 2015
Year and Model: 2008 s40 r design
Location: coventry

Post by dylan_iker »

doublebug wrote:If the new module and software fits your car and this module does not have any error codes stored the message should go away.
thank you, so if the software dont match, does it need to be programmed and will any mechanic be able to do it or i will need to go to the main dealer?

doublebug
Posts: 347
Joined: 19 July 2013
Year and Model: XC90 2007 D5
Location: Belarus
Been thanked: 7 times

Post by doublebug »

mechanic should have VIDA with online subscription.
If not go to the dealer or ...
If you have questions about Volvo firmware ask me. I may know an answer :)

dylan_iker
Posts: 6
Joined: 2 December 2015
Year and Model: 2008 s40 r design
Location: coventry

Post by dylan_iker »

so it cannot be done with an obd or any other dignostic tools

doublebug
Posts: 347
Joined: 19 July 2013
Year and Model: XC90 2007 D5
Location: Belarus
Been thanked: 7 times

Post by doublebug »

With some generic scanner you can clear error codes only (if scanner supports SRS modules)
If you have questions about Volvo firmware ask me. I may know an answer :)

dylan_iker
Posts: 6
Joined: 2 December 2015
Year and Model: 2008 s40 r design
Location: coventry

Post by dylan_iker »

Hiya, today I replaced my sirs control module with a second hand car off a vehicle that never had an accident, but the light are still on, This time will the lights go off if I go to a local garage?

Post Reply
  • Similar Topics
    Replies
    Views
    Last post